manualshive.com logo in svg

Lenovo HX1310, Installation And Service Manual

Share
Download
Lenovo HX1310 Installation And Service Manual Download Page 166

Step 5.

Carefully insert the tab on the retention bracket into the slot on the LCD panel assembly and rotate
it counterclockwise until it clicks into place.

Media cage

Retention bracket

Figure 77. Retention bracket installation

Step 6.

Connect the LCD system information display panel cable to the back of the LCD system
information display panel.

Step 7.

Carefully push the media cage back into the chassis (see “Replacing the media cage” on page
143). Remember to reconnect the cables that were removed from the system board.

Step 8.

Reinstall the cover (see “Replacing the cover” on page 105).

Step 9.

Slide the server into the rack.

Step 10. Reconnect the power cords and any cables that you removed.

Step 11. Turn on the peripheral devices and the server.

Removing the COM port bracket

Use this information to remove the COM port bracket.

To remove the COM port bracket, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 100.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the cover (see “Removing the cover” on page 104).

152

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands