Lenovo Flex System x220 Installation And Service Manual Download Page 668 | Manualshive

Page: 668 / 714

background image

000

000

000

000

000

0000000000

0000000000

0000000000

0000000000

0000000000

0000000000

0000000000

Captive
screws

Fabric
connector

Step 1.

Remove the cover (see “Removing the compute node cover” on page 643).

Step 2.

Locate the fabric connector on the system board (see “System-board layouts” on page 17).

Step 3.

Using a #1 Phillips screwdriver, loosen the four captive screws that secure the fabric connector.

Step 4.

Lift the fabric connector from the system board and store it in a safe place.

If you are instructed to return the fabric connector, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

If you have removed the fabric connector to install an I/O expansion adapter in I/O expansion connector 1,
keep the fabric connector in a safe place for future use.

Installing a fabric connector

Use this information to install a fabric connector.

Before you install a fabric connector, complete the following steps:

1. Read “Safety” on page iii and “Installation guidelines” on page 637.

2. If the compute node is installed in an Flex System chassis, remove it (see “Removing a compute node

from a chassis” on page 639 for instructions).

3. Carefully lay the compute node on a flat, static-protective surface, orienting the compute node with

the bezel pointing toward you.

4. Obtain a #1 Phillips screwdriver.

To install a fabric connector, complete the following steps.

660

Flex System x220 Compute Node Installation and Service Guide

«
...
666
667
668
669
670
...
»

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x220

Brand: Gateway Pages: 26

System x3100 M4

Brand: IBM Pages: 332

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

UniServer E3200 G3

Brand: H3C Pages: 401

Brand: Supermicro Pages: 118

419452u - Servers System X3250 M2 Xeon...

Brand: IBM Pages: 84

Eternus DX80 S2

Brand: Fujitsu Pages: 186

Brand: Fujitsu Pages: 242

Brand: D-Link Pages: 40

Brand: NewTek Pages: 206

Brand: EVS Pages: 198

Brand: Chip PC Pages: 4

Brand: TAG Pages: 6

InfiniteStorage 3000

Brand: Silicon Graphics Pages: 50

Brand: IBM Pages: 136

Brand: Intel Pages: 75

Brand: Elastix Pages: 5

QuantaGrid Series

Brand: QCT Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands