Lenovo Flex System x220 Installation And Service Manual Download Page 53 | Manualshive

Page: 53 / 714

background image

The ServerGuide program performs the following tasks:

• Sets system date and time

• Detects installed optional hardware devices and provides updated device drivers for most adapters

and devices

• Provides diskette-free installation for supported Windows operating systems

• Includes an online readme file with links to tips for hardware and operating-system installation

Typical operating-system installation

The ServerGuide program can reduce the time it takes to install an operating system. It provides the device
drivers that are required for your hardware and for the operating system that you are installing. This section
describes a typical ServerGuide operating-system installation.

Note:

Features and functions can vary slightly with different versions of the ServerGuide program.

1. After you have completed the setup process, the operating-system installation program starts. (You

will need your operating-system CD to complete the installation.)

2. The ServerGuide program stores information about the compute node model, IMM2, hard disk drive

controllers, and network adapters. Then, the program checks the CD for newer device drivers. This
information is stored and then passed to the operating-system installation program.

3. The ServerGuide program presents operating-system partition options that are based on your

operating-system selection and the installed hard disk drives.

4. The ServerGuide program prompts you to insert your operating-system CD and restart the compute

node. At this point, the installation program for the operating system takes control to complete the
installation.

Installing the operating system without using ServerGuide

Use this information to install the operating system on the compute node without using ServerGuide.

If you have already configured the compute node hardware and you are not using the ServerGuide program
to install your operating system, you can download operating-system installation instructions for the
compute node from http://www.lenovo.com/support.

Using Lenovo ServerGuide Scripting Toolkit

The ServerGuide Scripting Toolkit is a collection of system-configuration tools and installation scripts that
you can use to deploy software to your Flex System compute node in a repeatable, predictable manner.
When the ServerGuide Scripting Toolkit is used with Lenovo ServerGuide, it provides a total solution for
deploying Flex System compute nodes in an unattended mode.

For more information about using the ServerGuide Scripting Toolkit, see https://support.lenovo.com/us/en/
documents/LNVO-CENTER.

Installing the operating system

45

«
...
51
52
53
54
55
...
»

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x220

RS/6000 7043 43P Series

Brand: IBM Pages: 322

System x3400 M3 Types 7378

Brand: IBM Pages: 45

Brand: IBM Pages: 92

Express5800/R310e-E4

Brand: NEC Pages: 86

Brand: Lantech Pages: 49

Thin Client 166

Brand: Tangent Pages: 2

Brand: Supermicro Pages: 113

Brand: MSI Pages: 18

Brand: IBM Pages: 1730

Brand: HPE Pages: 4

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: Polycom Pages: 11

Brand: MSI Pages: 54

Brand: MSI Pages: 86

m330 media server

Brand: Wadia Pages: 24

Brand: NexPath Pages: 166

SGI 1200 Series

Brand: Silicon Graphics Pages: 64

Rackable C2112-4RP9

Brand: Silicon Graphics Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands