Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 219

Page: 219 / 313

Note:

You can view the LEDs from the advanced management module web interface. For more information,

see the

Advanced Management Module Installation and User's Guide

Viewing the light path diagnostics LEDs

Use this information to locate and identify the light path diagnostics LEDs.

Before you work inside the blade server to view light path diagnostics LEDs, read “Safety” on page v and
“Installation guidelines” on page 65.

If an error occurs, view the light path diagnostics LEDs in the following order:

Step 1. Look at the control panel on the front of the blade server (see “Blade server controls and LEDs” on

page 7).

Power button / LED

KVM select
button / LED

Media tray select
button / LED

Activity LED

Location LED

Information LED

Fault LED

• If the information LED is lit, it indicates that an Automatic BIOS Recovery has occurred. Perform

these steps to resolve the issue:

1. Attempt to update the server firmware again (see “Updating firmware and device drivers” on

page 30).

2. Reseat the blade server (see “Removing the blade server from the BladeCenter chassis” on

page 66 and “Installing a blade server in a BladeCenter chassis” on page 67).

3. (Trained service technician only) Replace the system board (see “Removing the system-

board assembly - BladeCenter HX5” on page 140 and “Installing the system-board
assembly - BladeCenter HX5” on page 142).

• If the fault LED is lit, it indicates that an error has occurred; view the light path diagnostics panel

and LEDs to isolate the failing component.

Step 2. Look for LEDs through the front bezel, which indicate microprocessor errors.

Step 3. To view the light path diagnostics panel and LEDs, complete the following steps:

a. Remove the blade server or scalable blade complex from the BladeCenter chassis, (see

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions).

b. Carefully lay the blade server on a flat, static-protective surface.

c. Open the blade server cover (see “Removing the blade server cover” on page 71 for

instructions).

d. Press the power button. When you press the power button, LEDs on the system board will be

lit if there are any hardware-related issues.

Chapter 5

Diagnostics

203

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands