Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 17 | Manualshive

Page: 17 / 313

background image

Chapter 1. Introduction

The IBM BladeCenter HX5 Type 7873, 7872, 1910, and 1909 blade servers are high-density, scalable blade
servers ideally suited for high performance and virtualized environments. A BladeCenter HX5 can be
combined with the IBM MAX5 for BladeCenter expansion blade to provide memory expansion for medium to
large businesses.

The IBM BladeCenter HX5 Type 7873, 7872, 1910, and 1909 blade servers support the following
components:

• Up to two multi-core microprocessors

• Up to 16 memory modules (DIMMs)

Note:

Combining a BladeCenter HX5 and an IBM MAX5 expansion blade supports up to 40 DIMMs.

• Up to two internal solid state drives (SSDs)

• Expansion devices, such as:

– Horizontal-compact-form-factor (CFFh) expansion cards

– Vertical-combination-I/O (CIOv) expansion cards

In addition, you can combine two BladeCenter HX5 blade servers to form a

scalable blade complex

.

Combining two BladeCenter HX5 blade servers in a scalable blade complex provides for

FlexNode

partitioning

. With FlexNode partitioning, you can deploy the blade servers as a single server or as two

independent servers, without changing the physical configuration. The ability to switch between single-
partition mode and stand-alone mode is provided through the advanced management module web interface.
For more information about scalable blade complexes and FlexNode partitioning, see “Working with a
scalable blade complex” on page 16.

Note:

You can combine two BladeCenter HX5 blade servers to form a scalable blade complex. You can also

combine a single BladeCenter HX5 blade server with an IBM MAX5 expansion blade for expanded memory
access. You cannot attach an IBM MAX5 to a scalable blade complex.

For more information about the advanced management module web interface, see the http://www.ibm.com/
systems/ support/supportsite.wss/docdisplay? brandind=5000008&lndocid=MIGR-5073887.

The BladeCenter HX5 blade server is supported in the following BladeCenter chassis:

• IBMBladeCenter H

• IBMBladeCenter HT

• IBMBladeCenter S

For the latest information about the BladeCenter chassis that support the BladeCenter HX5 blade server, see
http://www.ibm.com/ servers/eserver/serverproven/compat/us/.

This

Problem Determination and Service Guide

provides information about:

•  Starting and configuring the blade server
•  Installing and removing hardware devices
•  Performing troubleshooting on the blade server
Packaged with the blade server are software CDs that help you to configure hardware, install device drivers,
and install the operating system.

To download the latest firmware and device drivers, complete the following steps.

© Copyright Lenovo 2017

1

«
...
15
16
17
18
19
...
»

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

NEC Express5800 Series

Brand: NEC Pages: 4

NEC Express5800 Series

Brand: NEC Pages: 21

NEC Express5800 Series

Brand: NEC Pages: 10

NEC Express5800 Series

Brand: NEC Pages: 22

NEC Express5800 Series

Brand: NEC Pages: 71

NEC Express5800 Series

Brand: NEC Pages: 166

NEC Express5800 Series

Brand: NEC Pages: 16

8835 - Eserver 325 - 1 GB RAM

Brand: IBM Pages: 68

Brand: IBM Pages: 42

Brand: Omneon Pages: 2

eServer 380 xSeries

Brand: IBM Pages: 112

Brand: Fibrenetix Pages: 17

SUPERO SuperServer 6026TT-H6IBQRF

Brand: Supero Pages: 110

FlexWATCH 1110L

Brand: Seyeon Technology Pages: 96

iPlanet Web Server

Brand: Sun Microsystems Pages: 62

AlphaServer ES47

Brand: HP Pages: 76

AlphaServer GS80

Brand: HP Pages: 88

Brand: HP Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands