Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 136

Page: 136 / 313

Expansion
card

Expansion
card
standoff

Release
lever

Step 11. Lift the card away from the expansion-card standoff.

Step 12. If you are instructed to return the CFFh expansion card, follow all packaging instructions, and use

any packaging materials for shipping that are supplied to you.

Removing a CIOv expansion card

Use these instructions to remove a CIOv expansion card from the blade server.

The following illustration shows how to remove a vertical-combination-I/O (CIOv) expansion card.

Expansion
card

To remove a CIOv expansion card, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If you are removing the CIOv card from a blade server that is the bottom blade server in a scalable

blade complex, disassemble the blade complex (see “Disassembling a scalable blade complex” on
page 68 for instructions).

Step 5. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 6. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 7. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

120

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Brands by name

Popular brands