Lenovo 7Z70 Reference Download Page 196

Page: 196 / 212

Severity: Error

User Action:

1. Reboot system and run the test again later.

2. If this message is still reported, please run the latest version of SMART tool on OS which is open

source tool and could be downloaded from website to check hard drive status.

3. If the problem persists, please contact technical support.

•

FQXPMSD0010M: uEFI is timeout while LXPM send command to test hard drive.

Severity: Error

User Action:

1. Reboot system and run the test again later.

2. If this message is still reported, please run the latest version of SMART tool on OS which is open

source tool and could be downloaded from website to check hard drive status.

3. If the problem persists, please contact technical support.

•

FQXPMSD0011M: The hard drive is not supported by uEFI while LXPM send command to test hard

drive.

Severity: Error

User Action:

1. Please check hard drive specification to see if the hard drive support ATA self-test feature.

2. If the problem persists, please contact technical support.

•

FQXPMSR0001K: Found unsupported RAID adapter.

Severity: Warning

User Action:

1. Check the following Lenovo support site for information on supported RAID adapters. http://www.

lenovo.com/us/en/serverproven/index.shtml

2. Ensure RAID adapter, LXPM, and UEFI firmware are at the latest levels.

3. If the problem persists, please contact technical support.

•

FQXPMSR0011K: Failed to change disk drives' state.

Severity: Warning

User Action:

1. Ensure LXPM and RAID adapter firmware are at the latest levels.

2. Ensure the state of the RAID adapter and disk drives are both healty.

3. Verify proper physical connection of the disk drive, SAS expander (if applicable) and RAID adapter.

4. Ensure the operation to the special drive is legal or logical. (For example, you cannot change

Unconfigured BAD to Online satus)

5. Reboot the machine and retry to change disk drives' state.

6. If the problem persists, please contact technical support.

•

FQXPMSR0012I: Change disk drives' state successfully.

Severity: Info

192

ThinkSystem SR630 V2 Messages and Codes Reference

Summary of Contents for 7Z70





















































































































































































































Search results

Summary of Contents for 7Z70

Reviews:

Related manuals for 7Z70

Brands by name

Popular brands

Lenovo 7Z70, Reference

Search results

Summary of Contents for 7Z70

Reviews:

Related manuals for 7Z70

Brands by name

Popular brands