manualshive.com logo in svg

Lenovo 7X69, Setup Manual

Share
Download
Lenovo 7X69 Setup Manual Download Page 57

4.  With SATA/SAS RAID adapter (8i)

Figure 42. Cable routing, AnyBay bac AnyBay backplane

Table 36.  Cables and adapters for routing

1 

4U PCIe riser card

6 

PCIe switch card

2 

SATA/SAS RAID adapter (8i)

7 

SATA/SAS signal cables (720 mm)

3 

NVMe connectors on the processor and memory 

expansion tray

8 

NVMe signal cables for PCIe switch card

4 

Direct NVMe signal cables for processor and 

memory expansion tray

9 

SATA/SAS signal cables (720 mm)

5 

SATA/SAS RAID adapter (8i)

Parts list

Use the parts list to identify each of the components that are available for your server.

For more information about ordering the parts shown in 

Figure 43 “Server components” on page 50

:

https://datacentersupport.lenovo.com/products/servers/thinksystem/sr860

Note:

Depending on the model, your server might look slightly different from the illustration.

Chapter 2

.

Server components

49

Summary of Contents for 7X69













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands