manualshive.com logo in svg

Lenovo 7X69, Setup Manual

Share
Download
Lenovo 7X69 Setup Manual Download Page 152

RAID configuration

Using a Redundant Array of Independent Disks (RAID) to store data remains one of the most common and 

cost-efficient methods to increase server's storage performance, availability, and capacity. 

RAID increases performance by allowing multiple drives to process I/O requests simultaneously. RAID can 
also prevent data loss in case of a drive failure by reconstructing (or rebuilding) the missing data from the 
failed drive using the data from the remaining drives.

RAID array (also known as RAID drive group) is a group of multiple physical drives that uses a certain 
common method to distribute data across the drives. A virtual drive (also known as virtual disk or logical 
drive) is a partition in the drive group that is made up of contiguous data segments on the drives. Virtual drive 
is presented up to the host operating system as a physical disk that can be partitioned to create OS logical 
drives or volumes.

An introduction to RAID is available at the following Lenovo Press website:

https://lenovopress.com/lp0578-lenovo-raid-introduction

Detailed information about RAID management tools and resources is available at the following Lenovo Press 
website:

https://lenovopress.com/lp0579-lenovo-raid-management-tools-and-resources

Deploy the operating system

Several options are available to deploy an operating system on the server.

Available operating systems

•  Microsoft Windows Server
•  VMware ESXi
•  Red Hat Enterprise Linux
•  SUSE Linux Enterprise Server

Complete list of available operating systems: 

https://lenovopress.com/osig

. 

Tool-based deployment

• 

Multi-server

Available tools:  

–  Lenovo XClarity Administrator

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/compute_node_image_deployment.html

–  Lenovo XClarity Essentials OneCLI

http://sysmgt.lenovofiles.com/help/topic/toolsctr_cli_lenovo/onecli_r_uxspi_proxy_tool.html

–  Lenovo XClarity Integrator deployment pack for SCCM (for Windows operating system only)

https://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxci_deploypack_sccm.doc/dpsccm_c_endtoend_ 
deploy_scenario.html

• 

Single-server

Available tools:  

144

ThinkSystem SR860 Setup Guide

Summary of Contents for 7X69













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands