manualshive.com logo in svg

Lenovo 7X69, Setup Manual

Share
Download
Lenovo 7X69 Setup Manual Download Page 100

Note:

To maintain proper system cooling, if only one 4U PCIe riser assembly is installed, the 4U 

PCIe riser assembly filler must be installed to operate the server.

If you are instructed to return the component or optional device, follow all packaging instructions, and use 
any packaging materials for shipping that are supplied to you.

Remove the PCIe expansion tray

Use this procedure to remove the PCIe expansion tray.

Before removing the PCIe expansion tray:

1.  Read the safety information and installation guidelines (see 

“Safety” on page iii

and 

“Installation 

Guidelines” on page 56

).

2.  Turn off the server and peripheral devices and disconnect the power cords and all external cables (see 

“Power off the server” on page 132

).

3.  If the server is installed in a rack, remove the server from the rack.
4.  Remove the top cover (see 

“Remove the top cover” on page 89

).

To remove the PCIe expansion tray, complete the following steps:

Watch the procedure 

A video of this procedure is available at YouTube: 

https://www.youtube.com/watch?v=pIb0bIyfkDY&= 

PLYV5R7hVcs-Ak9fT8QAx8fLbEivizjRtp

.

92

ThinkSystem SR860 Setup Guide

Summary of Contents for 7X69













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands