Lenovo 6241 Installation And Service Manual Download

Page: 289 / 1990

To replace the storage book, complete the following steps:

1. Install the front operator panel on the new storage book (see “Replacing the front operator panel

assembly” on page 278).

2. Reinstall the front I/O panel (see “Replacing the front I/O panel (USB/video) assembly” on page 272).

3. Reinstall the drive backplanes (see “Replacing the 4x2.5-inch hot-swap drive backplanes” on page 243

and “Replacing the 8x1.8-inch hot-swap drive backplane assembly” on page 245).

4. Reinstall the storage book board. (see “Replacing the storage book board assembly” on page 276).

5. Reinstall the flash power modules, if any were removed (

6. Reinstall the adapters (see “Installing an adapter in the standard or half-length I/O book” on page 90).

7. Reconnect the cables to the adapters, the drive backplanes, and the storage book board.

8. Reinstall the storage book. Grasp the storage book and align it with the bay on the front of the server

and slide the storage book into the server. Place one hand under the center of the storage book to
support it while sliding it into the server.

Storage book

9. Rotate the cam handle all the way up and push it into the server until it locks in place.

10. Reinstall the drives in the front of the storage book.

11. Reconnect the power cord and any cables that you removed.

12. Turn on the peripheral devices and the server.

Removing the storage book board assembly

Use this information for instructions on how to remove the storage book board assembly.

To remove the storage book board assembly, complete the following steps:

1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables as necessary to replace the device.

3. Press the blue release button on the left EIA bezel of the storage book to release the cam handle; then,

lower the handle the way down.

4. Slide the storage book out of the server.

5. Disconnect the cables from the adapters.

Chapter 6

Removing and replacing components

275

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands