Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 256 / 1990

background image

Step 3.

Installing a 1.8-inch hot-swap drive:

a. Insert the drive into the drive bay with the label side of the drive facing up.

Drive tray
assembly

Release
latch

1.8-inch
filler panel

b. Push the drive into the drive bay and rotate the drive tray handle to the closed position and

ensure that the latch is in the locked position.

c. Reinstall the drive filler panel.

Step 4. Check the drive status LED to verify that the drive is operating correctly. If the amber drive status

LED for a drive is lit continuously, that drive is faulty and must be replaced. If the green drive activity
LED is flashing, the drive is being accessed.

Note:

If the server is configured for RAID operation using a ServeRAID adapter, you might have to

reconfigure your disk arrays after you install drives. See the ServeRAID adapter documentation for
additional information about RAID operation and complete instructions for using the ServeRAID
adapter.

Step 5. If you are installing additional hot-swap drives, do so now.

Removing the 4x2.5-inch hot-swap drive backplanes

Use this information for instructions on how to remove the 4x2.5-inch hot-swap drive backplane assembly.

To remove the 2.5-inch hot-swap drive backplanes, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44 .

Step 2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables as necessary to replace the
device.

242

System x3850 X6 and x3950 X6 Installation and Service Guide

«
...
254
255
256
257
258
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

Brand: Gateway Pages: 138

FrameSaver SLV 9126

Brand: Paradyne Pages: 24

Brand: SEH Pages: 5

BladeCenter PN41

Brand: IBM Pages: 88

Brand: IESC Pages: 109

Brand: Gigabyte Pages: 115

STRATOS S400-X44E

Brand: Quanta Computer Pages: 251

Brand: Sun Microsystems Pages: 90

Netfinity 1000-8477 21Y

Brand: IBM Pages: 268

SUPERSERVER 1018D-73MTF

Brand: Supero Pages: 124

TVS- 72XU Series

Brand: QNAP Pages: 56

Eternus DX80 S2

Brand: Fujitsu Pages: 186

Brand: Fujitsu Pages: 242

Force10 MXL Blade

Brand: Dell Pages: 2

Brand: Acer Pages: 52

Brand: Acer Pages: 94

Altos R700 Series

Brand: Acer Pages: 135

Brand: Acer Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands