Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 112 / 1990

background image

Storage book

Flash power
module slots

Step 6. Rotate the retention clip all the way up.

Step 7. Place the flash power module in the flash power module slot with the cable at the bottom and

facing the rear of the storage book.

Step 8. Connect one end of the cable extender, that comes with the power module, to the flash power

module cable and the other end of the cable extender to the adapter.

Step 9. Rotate the retention clip down and press it until it clicks in place.

Step 10. Reconnect the cables to the drive backplane.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 117.

Installing a RAID adapter flash power module in the standard I/O book

Use this information for instructions on how to install a RAID adapter flash power module in the standard I/O
book.

Note:

You can install up to three RAID flash power modules in the standard I/O book.

When you install RAID adapters that come with flash power modules in the standard I/O book , install the
flash power modules in the slots inside the standard I/O book air baffle to prevent them from overheating. To
install a RAID adapter flash power module in the air baffle, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

Step 2. Turn off the server and peripheral devices and disconnect all power cords and external devices.

Step 3. Remove the standard I/O book (see “Removing the standard I/O book” on page 224).

Step 4. Pull up on the air baffle top cover tab while pushing down on the bottom tab on the base of the air

baffle to remove the cover.

98

System x3850 X6 and x3950 X6 Installation and Service Guide

«
...
110
111
112
113
114
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Express5800 320La

Brand: NEC Pages: 206

Express5800/R110j-1

Brand: NEC Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands