Lenovo 10K9 Hardware Maintenance Manual Download Page 131

Page: 131 / 158

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 126.

Replacing the rear Wi-Fi antenna

To replace the rear Wi-Fi antenna, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 90.

3. Straighten the rear Wi-Fi antenna so that it can be more easily twisted.

4. Hold the thicker end of the rear Wi-Fi antenna and unscrew the Wi-Fi antenna from the rear of the

computer.

Figure 52. Removing the rear Wi-Fi antenna

5. Install the new rear Wi-Fi antenna to the rear Wi-Fi antenna cable connector attached on the rear

of the computer.

6. Adjust the angle of the rear antenna to lower the risk of breaking the antenna by accident.

Chapter 9

Installing or replacing hardware

123

Summary of Contents for 10K9






























































































































































Search results

Summary of Contents for 10K9

Reviews:

Lenovo 10K9, Hardware Maintenance Manual, Page: 131 / 158

Search results

Summary of Contents for 10K9

Reviews: