manualshive.com logo in svg

Lennox VEMD007N432U, Installation Manual

Share
Download
Lennox VEMD007N432U Installation Manual Download Page 10

Multi Variable Air Conditioners Duct Type Indoor Unit

 

6 

 

 

Fig4.2.1   

NOTES!

 

①

  Installation of the unit must be in accordance with National Electric Codes and local 

regulations. 

②

  Improper installation will affect unit’s performance, so do not install the unit by yourself. 

Please contact local dealer to arrange professional technicians for the installation. 

③

  Do not connect power until all installation work is finished. 

4.3 Requirements for Communication Line 

NOTES! 

If the unit is installed in the place with strong electromagnetic interference, shielded wire must be 

applied on the communication wire between indoor unit and wired controller. Twisted pair line with 
shielding function must be applied on the communication wire between indoor unit and indoor unit 
(outdoor unit).     

4.3.1 Select Communication Line for Indoor Unit and Wired Controller 

 

Fig4.3.1   

 
 
 
 
 
 
 
 
 

Summary of Contents for VEMD007N432U

































Reviews:

No comments

Brands by name

Popular brands

Load more brands