Lennox MERIT MLDVT-30NM Installation Instructions Manual Download Page 1

INSTALLATION INSTRUC

TIONS

Please read and understand these instructions  

before starting installation.

INSTALLER: Leave this manual with the appliance. 

CONSUMER: Retain this manual for future reference.
INSTALLATEUR : Laissez cette notice avec l’appareil. 

CONSOMMATEUR : Conservez cette notice pour 

consultation ultérieure.

AVERTISSEMENT : Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire au

minimum le risque d’incindie ou d’explosion ou pour

éviter tout dommage matériel, toute blessure ou la mort.   

 

 

 

 

 

WARNING: If the information in these instructions

is not followed exactly, a fire or explosion may

result, causing property damage, personal injury,

or death.   

WARNING /AVERTISSEMENT/AVISO

•  HOT GLASS WILL CAUSE 

  BURNS. 

• DO NOT TOUCH GLASS 

  UNTIL COOLED.

• NEVER ALLOW CHILDREN 

  TO TOUCH GLASS.

 

•  UNE SURFACE VITRÉE CHAUDE 

  PEUT CAUSER DES BRÛLURES. 

• LAISSER REFROIDIR LA SURFACE 

  VITRÉE AVANT D'Y TOUCHER. 

• NE PERMETTEZ JAMAIS À UN ENFANT 

  DE TOUCHER LA SURFACE VITRÉE.

•  EL VIDRIO CALIENTE 

  CAUSARÁ QUEMADURAS. 

• USTED DEBE NUNCA 

  TOCAR EL VIDRIO CALIENTE. 

• LOS NIÑOS DEBEN NUNCA 

  TOCAR EL VIDRIO.

- Do not store or use gasoline or other flammable

  vapors and liquids in the vicinity of this or any other

 appliance. 
- WHAT TO DO IF YOU SMELL GAS:

  • Do not try to light any appliance.

  • Do not touch any electrical switch; do not use any

    phone in your building.

  • Immediately call your gas supplier from a

  neighbor’s phone. Follow the gas supplier’s

  instructions.

  • If you cannot reach your gas supplier, call the fire

  department.
- Installation and service must be performed by a

  qualified installer, service agency or the gas supplier.

- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs

  ou liquides inflammables dans le voisinage de cet appareil

  ou de tout autre appareil. 
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

  • Ne pas tenter d’allumer d’appareil.

  • Ne touchez à aucan interrupteur. Ne pas vous servir des

    téléphones se trouvant dans le bâtiment où vous trouvez.

  • Appelez immédiatement votre fournisseur de gaz depuis

    un voisin. Suivez les instructions du fournisseur.

  • Si vous ne pouvez rejoindre le fournisseur de gaz,

    appelez le service des incindies.
- L’installation et l’entretien doivent être assurés par un

  installateur ou un service d’entretien qualifié ou par le

  fournisseur de gaz.

P/N 506015-10   Rev. A   03/2013 

This manual is one of a set of two supporting this product.  

Refer to P/N 506017-09 for Care and Operation Instructions.
Ce manuel est disponible en francais, simplement  

en faire la demande. Numéro de la pièce 506223-56.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile 

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the 

rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Report No. 100326540PRT-001

ELECTRONIC:

MILLIVOLT:

MLDVT Direct-Vent 

Gas Fireplaces

MLDVT30NE-2 

MLDVT35NE-2 

MLDVT40NE-2 

MLDVT45NE-2

MLDVT-30PM 

MLDVT-35PM 

MLDVT-35PM-FB 

MLDVT-40PM 

MLDVT-45PM

MLDVT-30NM 

MLDVT-35NM 

MLDVT-35NM-FB 

MLDVT-40NM 

MLDVT-40NM-FB 

MLDVT-45NM

MODELS

Summary of Contents for MERIT MLDVT-30NM





































Reviews: