Lennox 96G2UHE Installation Instructions Manual Download

Page: 29 / 62

507581-05

Page 29 of 62

Issue 2220

Figure 37. Exiting Exhaust and Intake Vent

(no common pressure zone)

Figure 38. Direct Vent Concentric Rooftop

Termination

71M80, 69M29 or 60L46 (US)

41W92 or 41W93 (Canada)

Minimum

Above Average

Snow

Accumulation

SHEET METAL STRAP

(Clamp and sheet metal strap

must be field installed to support

the weight of the termination kit.)

FLASHING

(Not Furnished)

CLAMP

FIELD-PROVIDED

REDUCER MAY BE REQUIRED

TO ADAPT DIFFERENT VENT

PIPE SIZE TO TERMINATION

1 1/2” (38mm) accelerator

provided on 71M80 & 44W92

kits for -045 and -070 models

12” (305mm)

INTAKE

AIR

EXHAUST

VENT

Figure 39.

Flush-Mount Side Wall Termination

51W11

2” EXTENSION FOR 2” PVC

PIPE1” EXTENSION FOR 3”

PVC PIPE

1-1/2” ACCELERATOR

(

all -45, -070 and -090 units)

FURNACE

EXHAUST

PIPE

FURNACE

INTAKE

PIPE

4''

GLUE EXHAUST

END FLUSH INTO

TERMINATION

FLAT

SIDE

Figure 40. Direct Vent Concentric Wall Termination

71M80, 69M29 OR 60L46 (US)

41W92 or 41W93 (Canada)

12” (305mm) Min.

above grade or

average snow

accumulation.

INTAKE

AIR

INTAKE

AIR

INTAKE

AIR

OUTSIDE

WALL

GRADE

CLAMP

(Not Furnished)

FIELD-PROVIDED

REDUCER MAY BE REQUIRED

TO ADAPT DIFFERENT VENT

PIPE SIZE TO TERMINATION

EXHAUST

VENT

1-1/2” (38mm) accelerator

provided on 71M80 & 44W92

kits for -045 and -070 models

EXHAUST

VENT

Figure 41. Optional Vent Termination for Multiple

Unit Installation of Direct Vent Wall Termination

EXHAUST

VENT

INTAKE

AIR

5-1/2”

(140mm)

Front View

12”

(305MM)

5”

(127MM)

18” MAX.

(457MM)

EXHAUST VENT

INTAKE

AIR

Inches (MM)

Side View

12” (305MM) Min.

above grade or

average snow

accumulation.

optional intake elbow

Figure 42. Direct Vent Application Using Existing

Chimney

3” - 8”

(76MM-

203MM)

STRAIGHT-CUT OR

ANGLE-CUT IN DIRECTION

OF ROOF SLOPE *

SHOULDER OF FITTINGS

PROVIDE SUPPORT

OF PIPE ON TOP PLATE

INTAKE PIPE

INSULATION (optional)

SHEET

METAL TOP

PLATE

Minimum 12” (305MM)

above chimney top

plate or average snow

accumulation

8” - 12”

(203MM - 305MM)

3”-8”

(76MM-203MM)

INSULATE

TO FORM

SEAL

EXTERIOR

PORTION OF

CHIMNEY

ALTERNATE

INTAKE PIPE

NOTE:

Do not discharge exhaust gases directly into any chimney

or vent stack. If vertical discharge through an existing unused

chimney or stack is required, insert piping inside chimney until

the pipe open end is above top of chimney and terminates as

illustrated. In any exterior portion of chimney, the exhaust vent

must be insulated.

Summary of Contents for 96G2UHE































































Search results

Summary of Contents for 96G2UHE

Reviews:

Related manuals for 96G2UHE

Brands by name

Popular brands

Lennox 96G2UHE, Installation Instructions Manual

Search results

Summary of Contents for 96G2UHE

Reviews:

Related manuals for 96G2UHE

Brands by name

Popular brands