Lennox 045-08 Installation Instructions Manual Download Page 6

Page: 6 / 60

507270-03

Page 6 of 60

Issue 1917

General

These instructions are intended as a general guide and do

not supersede local codes in any way. Consult authorities

having jurisdiction before installation.

In addition to the requirements outlined previously, the

following general recommendations must be considered

when installing one of these furnaces:

•

Place the furnace as close to the center of the air

distribution system as possible. The furnace should

also be located close to the vent termination point.

•

When the furnace is installed in non-direct vent

applications, do not install the furnace where drafts

might blow directly into it. This could cause improper

combustion and unsafe operation.

•

When the furnace is installed in non-direct vent

applications, do not block the furnace combustion air

opening with clothing, boxes, doors, etc. Air is needed

for proper combustion and safe unit operation.

•

When the furnace is installed in an attic or other

insulated space, keep insulation away from the

furnace.

•

When the furnace is installed in an unconditioned

space, consider provisions required to prevent freezing

of condensate drain system.

NOTE:

The Commonwealth of Massachusetts stipulates

these additional requirements:

•

Gas furnaces shall be installed by a licensed plumber

or fitter only.

•

The gas cock must be “T handle” type.

•

When a furnace is installed in an attic, the passageway

to and service area surrounding the equipment shall

be floored.

These units should not be installed in areas normally

subject to freezing temperatures.

CAUTION

Use of Furnace as a Construction Heater

Units may be used for heating of buildings or structures

under construction, if the following conditions are met to

ensure proper operation.

DO NOT USE THE UNIT FOR CONSTRUCTION HEAT

UNLESS ALL OF THE FOLLOWING CRITERIA ARE

MET:

a. Furnace must be in its final location. The vent system

must be permanently installed per these installation

instructions.

b. Furnace must be installed as a two pipe system

and one hundred percent (100%) outdoor air must

be provided for combustion air requirements during

construction.

c. A room thermostat must control the furnace. The use

of fixed jumpers that will provide continuous heating is

prohibited.

d. The input rate and temperature rise must be set per

the furnace rating plate.

e. Supply and Return air ducts must be provided and

sealed to the furnace. Return air must be terminated

outside of the space where furnace is installed.

f. Return air temperature range between 60°F (16°C)

and 80°F (27°C) must be maintained.

g. MERV 11 or greater air filters must be installed in

the system and must be regularly inspected and

maintained (e.g., regular static checks and replaced at

end of life) during construction.

h. Blower and vestibule access panels must be in place

on the furnace at all times.

i. The furnace heat exchanger, components, duct

system, and evaporator coils must be thoroughly

cleaned following final construction clean−up.

j. Air filters must be replaced upon construction

completion.

k. All furnace operating conditions (including ignition,

input rate, temperature rise and venting) must

be verified in accordance with these installation

instructions.

EQUIPMENT

MAY

EXPERIENCE

PREMATURE

COMPONENT FAILURE AS A RESULT OF FAILURE TO

FOLLOW THE ABOVE INSTALLATION INSTRUCTIONS.

FAILURE TO FOLLOW THE ABOVE INSTALLATION

INSTRUCTIONS VOIDS THE MANUFACTURER’S

EQUIPMENT LIMITED WARRANTY. ALLIED AIR

DISCLAIMS ALL LIABILITY IN CONNECTION WITH

INSTALLER’S FAILURE TO FOLLOW THE ABOVE

INSTALLATION INSTRUCTIONS.

NOTWITHSTANDING THE FOREGOING, INSTALLER

IS RESPONSIBLE FOR CONFIRMING THAT THE USE

OF CONSTRUCTION HEAT IS CONSISTENT WITH

THE POLICIES AND CODES OF ALL REGULATING

ENTITIES. ALL SUCH POLICIES AND CODES MUST BE

ADHERED TO.

Summary of Contents for 045-08





























































Search results

Summary of Contents for 045-08

Reviews:

Related manuals for 045-08

Brands by name

Popular brands

Lennox 045-08, Installation Instructions Manual

Search results

Summary of Contents for 045-08

Reviews:

Related manuals for 045-08

Brands by name

Popular brands