manualshive.com logo in svg

Leica Geosystems RoadRunner, Technical Reference Manual, Page: 127 / 342

Share
Download
Leica Geosystems RoadRunner Technical Reference Manual Download Page 127

Configuring

RoadRunner

127

6.2.2

The Posit Page (for TPS only)

Description

This allows the instrument to aim at the position to stake/check. Refer to "6.5 Auto Posi-
tioning (TPS only)" for information on the different positioning types. This functionality is only 
available for motorised instruments.

The Posit page

CONT (F1)

To confirm the changes and move to the previous 
screen.

Field

Option

Description of Field

Auto Position

Type of automatic positioning used.

NONE

No auto position.

2D (Hz)

Instrument positions horizontally.

3D (Hz & V)

Instrument positions horizontally and vertically.

2D + Meas

Instrument positions horizontally and finds the 
height by iterative distance measurements. Refer to 
"6.5.2 Auto Position 2D + Measure".

Advanced

Allows to keep certain values of the current position 
to remain constant.

 

Refer to "6.5.3 Auto Position 

Advanced".

Summary of Contents for RoadRunner























































































































































































































































































































































Reviews:

No comments