Leica Geosystems BLK3D User Manual Download Page 64

Page: 64 / 70

CAUTION

Changes or modifications not expressly approved by Leica Geosystems for

compliance could void the user's authority to operate the equipment.

CAUTION

Only use chargers recommended by the manufacturer to charge the batteries.

20.6

Laser Classification

20.6.1

General

The following chapters provide instructions and training information about

laser safety according to international standard IEC 60825-1 (2014-05) and

technical report IEC TR 60825-14 (2004-02). The information enables the per-

son responsible for the product and the person who actually uses the equip-

ment, to anticipate and avoid operational hazards.

☞

According to IEC TR 60825-14 (2004-02), products classified as laser

class 1, class 2 and class 3R do not require:

•

laser safety officer involvement,

•

protective clothes and eyewear,

•

special warning signs in the laser working area

if used and operated as defined in this User Manual due to the low

eye hazard level.

☞

National laws and local regulations could impose more stringent

instructions for the safe use of lasers than IEC 60825-1 (2014-05)

and IEC TR 60825-14 (2004-02).

20.6.2

BLK3D

The laser product built into the product produces a visible red laser beam

which emerges from the front of the product.

The laser product described in this section is classified as laser class 2 in

accordance with:

•

IEC 60825-1 (2014-05): “Safety of laser products”

These products are safe for momentary exposures but can be hazardous for

deliberate staring into the beam. The beam may cause dazzle, flash-blindness

and after-images, particularly under low ambient light conditions.

Description

Value

Wavelength

655 nm

Maximum radiant power

0.95 mW

Pulse duration

>400 ps

Pulse repetition frequency (PRF)

320 MHz

Beam divergence

0.16 x 0.6 mrad

General

Safety Directions

Summary of Contents for BLK3D







































































Search results

Summary of Contents for BLK3D

Reviews:

Brands by name

Popular brands

Leica Geosystems BLK3D, User Manual

Search results

Summary of Contents for BLK3D

Reviews:

Brands by name

Popular brands