Leica BIOSYSTEMS HistoCore BIOCUT Instructions For Use Manual Download Page 80

Page: 80 / 90

Version 1.7, Revision K

Cleaning and Maintenance

8.1

Cleaning the instrument

Warning

The liquids go into the interior of the instrument.

Serious injury of instrument/persons, or specimen damage.

• Ensure that liquids do not enter the interior of the instrument during operation and maintenance.

Warning

Knife/blade was not removed when knife/blade holder was uninstalled from the microtome.

Serious injury of persons due to contact with extremely sharp knife/blade.

• Before uninstalling the knife/blade holder from the microtome always make sure to detach the knife/

blade wearing cut-resistant gloves and store the knife/blade in a safe place.

Warning

Knife/blade stored in inappropriate manner.

Serious injury of persons, for example, due to unexpected fall off.

• Always store knife/blade in an appropriate place when not using them, for example, store it in the

dedicated knife case.

• Never place a knife anywhere with the cutting edge facing upwards and never try to catch a falling

knife.

Warning

Knife/blade holder falling off the instrument.

Serious injury of persons and/or property damage.

• If the knife/blade holder is not fixed, for example, during installation or cleaning, pay special

attention that the knife/blade holder is not falling off.

• Whenever possible, fix the knife/blade holder to avoid falling off.

Caution

Use of improper solvents or cleaners, or sharp/hard tools to clean the instrument or accessories.

Potential instrument malfunction or delay of diagnosis.

• Do not use any solvents containing acetone or xylene for cleaning.

• When using cleaners, please comply with the safety instructions of the manufacturer and the

laboratory safety regulations.

• Never use a sharp or hard tool to scrape the instrument surface.

• Never soak the accessories in any cleaning solvent or water.

• Clean steel knives using an alcohol-based solution or acetone.

• For cleaning and removal of paraffin, do not use xylene or cleaning fluids containing alcohol (for

example glass cleaner).

Summary of Contents for HistoCore BIOCUT



























































































Search results

Summary of Contents for HistoCore BIOCUT

Reviews:

Brands by name

Popular brands

Leica BIOSYSTEMS HistoCore BIOCUT, Instructions For Use Manual

Search results

Summary of Contents for HistoCore BIOCUT

Reviews:

Brands by name

Popular brands