Wattstopper
®
High Bay • Line Voltage • Passive Infrared
IP65 Occupancy Sensors for Wet Locations
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24140 – 08/17 rev. 2
Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: HB330W, HB340W, HB350W
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
1. Review the ADJUSTMENTS section and complete any
necessary DIP switch setting changes.
2. Mount the sensor so the lens is below the edge of the fixture
and away from the lamps. Heat from the lamps could affect
the sensor operation.
Make sure that you have the appropriate accessories for the sensor mounting
configuration. (See Mounting Options.)
3. Assemble any necessary mounting accessories and attach them to the sensor
module. Make sure that the flying leads from the sensor module cable are
accessible inside the fixture.
4. Connect the line voltage and load wires to the sensor leads as shown in the
applicable Wiring Diagram for the sensor module.
• Do not allow bare wire to show.
• Make sure all connections are secure.
• Check all gaskets for watertight fit.
5. Check sensor operation. Refer to the TESTING section.
6. Attach the Lens to the HB3x0W as shown in the sensor assembly drawing.
DESCRIPTION AND OPERATION
The HB3x0W occupancy sensors are designed for automatic lighting control in high bay wet location applications. The HB3x0W sensors
contain a passive infrared sensor (PIR). The sensors are modular and are made up of two parts, a Sensor Module (HB3x0W) and a
Lens (HBLxW).
The sensor module is available in three models for different line voltage applications: HB350W for 120/277VAC, HB340W for
347/480VAC, and HB330W for 208/240VAC.
The sensors use a set of DIP switches to set the time delay and PIR sensitivity as explained on page 3. The HB350W provides a single
load controlling relay. The HB330W and HB340W have two relays for phase switching.
SPECIFICATIONS
HB350W Voltages ..............................................................Voltages120/277VAC,60Hz
Load Requirements
@120VAC, 60Hz ........................................................0-800W ballast or tungsten
@277VAC, 60Hz .........................................................................0-1200W ballast
@120VAC ...................................................................................................1/6 hp
HB340W Voltages .......................................................................... 347/480VAC, 60Hz
Load requirements ......................................................................0-1200W ballast
HB330W Voltages .......................................................................... 208/240VAC, 60Hz
Load requirements ......................................................................0-1200W ballast
Wiring cable ....................................3 or 4-conductor 18AWG stranded, UL Style 2517
Unit Dimensions .................................................................. 4.08” diameter, 1.88” thick
Threaded nipple ........0.81” diameter, 0.40” long fits standard 1/2” electrical conduit fitting
Weight ............................................................................................0.28 lb (130 grams)
Material .........................................................ABS, UL94-5VA flame retardant material,
................. UV resistant, indoor use only, minimum plastic wall thickness 2.5mm
Environment ......................................................................................... IP65 Compliant
Operating temperature ................................................. -40°F (-40°C) to 131° F (55°C)
Storage temperature ..................................................... -40°F (-40°C) to 176°F (80°C)
Operating humidity ........................................................5 to 95% RH, non-condensing
Maximum Dew Point .................................................................................29°C (85°F)
US Patents: ........................................................................... 5,640,113 and 5,804,991
INSTALLATION OVERVIEW
CAUTION
TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE INSTALLING THE SENSOR.
HB3x0W (sensor module)
HBLxW (lens module)
L7 lens may require pliers
to remove the lens. (Grab
one of the fins to remove.)
Tightening ring
Sensor Assembly
DIP switches
HB3x0W L2W/
HB3x0W L3W
HB3x0W L7W
