manualshive.com logo in svg

LEGRAND vaddio 999-99800-100, Complete Manual, Page: 67 / 95

Share
Download
LEGRAND vaddio 999-99800-100 Complete Manual Download Page 67

streaming ip enable

Set or change the state of IP streaming.

Synopsis

streaming ip enable { get | on | off | toggle}

Parameters

get

Returns the current state of IP streaming

on

Enables IP streaming.

off

Disables IP streaming.

toggle

Changes the state of IP streaming (on if it was
off, or off if it was on).

streaming ip

enable toggle

has the same effect as

selecting the Enable IP Streaming checkbox in
the web interface.

Example

>

streaming ip enable on

> OK

Enables IP streaming.

>

streaming ip enable get

enabled: true

> OK

Returns the current state of IP streaming.

Maintenance and Troubleshooting Commands

The following commands are available for maintenance and troubleshooting:

n

network ping

n

system reboot

n

system factory-reset

n

version

version

Returns the current firmware version.

Synopsis

version

Example

>

version

Returns current firmware version information. Your camera may return slightly
different information.

62

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Summary of Contents for vaddio 999-99800-100
































































































Reviews:

No comments