manualshive.com logo in svg

LEGRAND vaddio 999-99800-100, Complete Manual, Page: 48 / 95

Share
Download
LEGRAND vaddio 999-99800-100 Complete Manual Download Page 48

Contacting Vaddio Technical Support

H

ELP PAGE

If you can't resolve an issue using your troubleshooting skills (or the

Troubleshooting

table in this manual),

we are here to help.

You’ll find information for contacting Vaddio Technical Support on the Help page. The model identifier and
the link for support information vary depending on the camera model.

Note

The Help page provides a link to our standard privacy notice. This product does not record or save video
files, and it does not store any identifying information other than what you may choose to enter on the
Room Labels page of the web interface. However, the camera’s IP address is considered “personally
identifiable information” for the purposes of the privacy notice. This information is stored for display to the
user, but not otherwise shared or transmitted.

43

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Summary of Contents for vaddio 999-99800-100
































































































Reviews:

No comments