manualshive.com logo in svg

LEGRAND vaddio 999-99800-100, Complete Manual, Page: 38 / 95

Share
Download
LEGRAND vaddio 999-99800-100 Complete Manual Download Page 38

Lighting and Image Quality Cheat Sheet

Here are some tips for using the CCU settings for lighting and image quality. For more detailed information
on each setting, see

Lighting Adjustments

and

Fine-Tuning Image Quality and Color

.

What do you need to correct?

Make this adjustment:

The image is too dark

Increase Iris (lower F-stop value)

Increase Iris Gain

The image looks washed out or faded

Decrease Iris (higher F-stop value)

Decrease Iris Gain

Increase Chroma

Decrease Gamma

The subject is silhouetted against a bright
background

Enable Backlight Compensation

Highlights and shadows look right, but mid-tones
are too dark.

Increase Gamma

Shadows are too dark

Enable Wide Dynamic Range (WDR)

Decrease Gamma

The image looks grainy

Decrease Detail

Decrease Iris Gain

"Soft focus" effect; the image looks unrealistically
smooth

Increase Detail

33

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Summary of Contents for vaddio 999-99800-100
































































































Reviews:

No comments