manualshive.com logo in svg

LEGRAND 999-9595-070, Manual, Page: 44 / 48

Share
Download
LEGRAND 999-9595-070 Manual Download Page 44

Restoring Factory Defaults

This operation returns the device to its original state.

n

Any settings you have customized will be lost.

n

Anyone who is logged in to the web interface is logged out.

n

You will need to do the initial device setup again to be able to communicate with the device.

You can restore factory defaults from the web interface (System page, Firmware tab) or by sending the
Telnet command

system factory-reset on

followed by

system reboot

. If you are not able to log

in to the device, contact Vaddio Technical Support.

If the password is unknown:

1. Disconnect power.

2. Press and hold the IP address button while reconnecting power; continue to hold the button for 15

seconds.

Operation, Storage, and Care

For smears or smudges on the product, wipe with a clean, soft cloth. Use a lens cleaner on the lens. Do
not use any abrasive chemicals.

Keep this device away from food and liquids.

Do not operate or store the device under any of the following conditions:

n

Temperatures above 104°F (40°F) or below 32°F (0°C)

n

High humidity, condensing or wet environments

n

Inclement weather

n

Severe vibration

n

In or on top of a pizza oven

n

Dry environments with an excess of static discharge

Do not attempt to take this product apart. There are no user-serviceable components inside.

Complete Manual for the OneLINK Bridge Express AV Interface

41

Summary of Contents for 999-9595-070

















































Reviews:

No comments