LEGRAND 5 735 04 Technical Data Manual Download

Page: 6 / 38

CONTENTS

6/38

Cat. No(s).: 5 735 04/05

5 735 12/13

KNX

Arteor 4 and 6 touches glass controls

Technical data sheet: S000090563EN-2

Updated: 07/06/2016

Created : 27/07/2015

8. NFC SETTING

The different function parameters can be set using NFC after

downloading the “Close Up” app from Google Play or legrandoc.com

with an NFC compatible Android mobile device.
The device does not need be connected to the mains during parameter

setting.

BEEP

1. Hold the mobile device close to the NFC symbol.

2. The scanned device's data is displayed.

• Copying a device (not connected to the mains)

This function is used to copy the configuration from one device to another.

1. After selecting “Tools”, choose “Duplicate”.

8. NFC SETTING (continued)

• Copying a device (not connected to the mains) (continued)

2. Then tag the target device (where the configuration is to be imported)

and confirm the target device with OK.

3. Hold the mobile away from the device and then bring it closer to load

the configuration, which completes the action.

9. STANDARDS AND APPROVALS

• Complies with standard IEC 60 669.2.1

• Marking: KNX EIB, CE

Note:

All technical information is available at

www.legrandoc.com

10. MAINTENANCE

Clean the surface with a cloth.

Do not use acetone, tar-removing cleaning agents or trichloroethylene.

Caution:

Always test before using other special cleaning products.

Summary of Contents for 5 735 04







































Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands

LEGRAND 5 735 04, Technical Data Manual

Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands