1/5
CONTENTS
Miniature PIR presence detector - ON/OFF
Technical data sheet: S000105121EN-1
Updated: 26/11/2018
Created: 07/11/2018
Cat. No(s): 0 489 54
128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex
Tel: +33(0)5 5 55 06 87 87 Fax: +33(0)5 55 06 88 88
www.legrand.com
CONTENTS Page
1. Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Technical characteristics . . . . . . . . . . . . . . . . . 1
3. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
6. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
7. Parameter settings. . . . . . . . . . . . . . . . . . . . . . . 3
8. Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
10. Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1. USE
This miniature PIR (passive infrared) presence detector provides
automatic control of lighting loads with optional manual control.
This model can be used for switching control of incandescent,
fluorescent and compact fluorescent loads.
The unit detects movement using a PIR sensor and turns the load on.
When an area is no longer occupied, the load will switch off after an
adjustable timeout period.
These units come complete with accessories allowing flush mounting in
suspended ceilings or surface mounting on ceilings, or side mounting
on a luminaire.
All functionality is fully programmable using an infrared configurator.
2. TECHNICAL CHARACTERISTICS
PIR sensor
Detects movement within the unit’s detection range, allowing load
control in response to changes in occupancy.
IR receiver
Receives control and programming commands from the infrared
configurator.
Light level sensor
Measures the overall Lux level in the detection area.
LED status
The LED flashes red to indicate the following:
RJ11 connector
The sensor head has an RJ11 socket for connection to the power supply.
Power supply
This power supply has a 6 A relay. It also has connections for an auxiliary
switch that can be used to turn on the lighting manually.
Walk test LED active
When movement is detected
Valid setting received
2. TECHNICAL CHARACTERISTICS (CONTINUED)
Sensor head
Power supply
Dimensions
See dimensions section
Weight
Sensor head: 0.02 kg
Power supply: 0.08 kg
Power supply
230 VAC +/-10%
Frequency
50 Hz
Maximum load
6 A resistive and incandescent lighting
3 A fluorescent lighting
2 A compact fluorescent lighting
2 A low-energy lighting
2 A low-voltage lighting (switches
transformer primary)
1 A fans and ventilation equipment
NOTE: For fluorescent lighting, 6 loads
maximum recommended. Total power
factor correction capacitance must not
exceed 40 µF
Power consumption
ON 816 mW, OFF 837 mW
Terminal capacity
1.5 mm²
PIR lens
IR receiver
Light level sensor
Status LED
