LEGRAND 0 488 34 Manual Download Page 1

1/7

Technical data sheet: S000088605EN-1  

Updated on:  

Created: 03/04/2015

Catalogue number(s): 0 488 34

SCS motion sensors  

Surface/wall mounting - PIR

  1. USe

This is a passive infrared (PIR) device adapted to detecting presence and 

measuring the level of natural light. 

It can be installed directly on a wall, flush-mounted in a wiring accessory 

box and installed in internal or external corners with fixing accessory 

Cat. No. 0 489 71.

It is suitable for indoor or outdoor passageways such as atriums, 

corridors, car parks, cellars, etc.

Main possible functions:

-  Switching/Dimming: in automatic mode, or manual mode in 

association with a control unit

-  Configuring the operating mode: Auto ON/OFF, Manual ON/Auto OFF, 

Walk-through

- Defining a light level threshold to be maintained

- Triggering scenarios according to presence/absence

The mode and settings are configured using configurators, with 

MHSuite and mobile configurators Cat. Nos. 0 882 30 or 0 882 35.

  2. TeChnICal ChaRaCTeRISTICS

Voltage: 27 V

=

No-load power consumption: 20 mA max.

Connection between the sensor and controller: BUS/SCS cable

Flush-mounting diameter:  65 mm without a flush-mounting box, 

68 mm with a flush-mounting box

Weight: 180 g

Impact resistance: IK04

Penetration by solid and liquid matter: IP55

Operating temperature: -5°C to +45°C

Storage temperature: -20°C to +70°C

Cover removed

ConTenTS 

Page

1. Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. Technical characteristics  . . . . . . . . . . . . . . . .1

3. Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

4. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

6. Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

7. Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

8. Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . .5

9. Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . .6

10. Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

11. Standards and certifications. . . . . . . . . . . . .7

12. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .7

IP55

PIR sensor

Light  

level cell

LEARN LED

IR transmission/

reception LED

Detection LED

LEARN button

  3. DImenSIonS

With protective cover

84

46.5

31

115.5

  4. ConneCTIon

BUS/SCS

Summary of Contents for 0 488 34








Reviews: