background image

2/11

CONTENTS

Technical data sheet: S000094312EN-1 

Updated: 

Created: 20/09/2017

Cat. No(s): 0 026 54

KNX modular dimmer 2 x 300 W

  1. USE

The KNX modular dimmer Cat No. 0 026 54 is used for controlling 

dimming on two circuits up to 300 W per channel.

It is compatible with incandescent bulbs, high and low voltage halogen 

lamps and dimmable LEDs.

The associated load (R, L or C type) is identified automatically, or 

manually by the user.

To check that the wiring is correct, each channel can be controlled 

locally on the controller by means of push-buttons and LEDs on the 

front panel.

The device operating parameters can be configured with ETS and 

modified using NFC technology via the Legrand Close Up app.
The main application program functions are as follows:

• Configuration of dimming speed

• Definition of min./max. dimming thresholds to ensure consistent 

dimming

• Configuration of the scene control function (8 scenes max. per 

channel)

• Definition of a hold threshold and a time delay

• Selection of the load state after a power failure

• Configuration of error message objects

• Configuration of time delay indicator objects

  2. TECHNICAL CHARACTERISTICS

2.1 Electrical characteristics 

• Voltage: 240V~

• Frequency: 50/60 Hz 

• Terminal type: screw 

• Terminal capacity: 1 x 2.5 mm2 or 2 x 1.5 mm2

• BUS consumption: 3 mA

• Table of loads which can be controlled (per channel)

R

(trailing or 

leading mode)

L

(leading mode)

Dimmable

Dimmable

Dimmable 

LED

 12 VAC

240 V~

Max.

300 W

200 VA 

or 30 

200 VA 

or 15 

300 VA

100 W 

or 8 

Min.

1 W

1 VA

1 VA

1 VA

1 W

T

(trailing mode)

L

(leading mode)

Dimmable

Dimmable

 Dimmable LED

 12 VAC

240 V~

Max. 200 VA or 30 

200 VA or 10 

75 W or 8 

Min.

1 VA

1 VA

1 W

1 - Halogen lamp

2 - ELV halogen lamp and LED lamp with separate electronic or 

ferromagnetic ballast

3 - Fluorescent tubes with dimmable separate electronic ballast

4 - Compact fluorescent bulbs with dimmable built-in electronic ballast

5 - ELV halogen lamp and LED lamp with dimmable separate electronic 

ballast

6 - LED bulb with dimmable built-in electronic ballast

(*)

  Only use transformers designed to operate with electronic switches.

(**)

  Only use dimmable LEDs with this logo 

 on the packaging.

   2.  TECHNICAL CHARACTERISTICS

 

(continued)

2.2 Mechanical characteristics

• IP 20 

• Number of modules: 4

• Weight: 170 g

2.3 Climate characteristics

• Operating temperature: -5°C to +45°C

2.4 NFC characteristics

• 13.56 MHz - ≤ 20 dBμA

Important:

Take the transformer losses into account when calculating the 

power. The transformers must be loaded at more than 60% of their 

power.

  3. DIMENSIONS

71.5 mm

67 mm

83 mm

90 mm

  4. CONNECTION

4.1 Single-phase wiring

300 W 

max.

300 W 

max.

29 V

 

=

Important:

Install a common circuit breaker for both channels since the neutrals 

are interconnected in the device.

/

/

(*)

(**)

1

5

6

2

3

4

Summary of Contents for 0 026 54












Reviews: