Refueling Precautions
•
Do NOT overfill the fuel tank as overflow creates a fire
hazard when spilled on hot components.
•
DO NOT smoke when refueling and never refuel when
the engine is running. Fuel is highly flammable and
should be handled with care. Death or serious injury
can occur due to explosion and/or fire.
•
DO NOT fill tank to capacity. Allow room for expansion
to reduce the risk of fuel expanding and spilling from
the tank.
•
Tighten fuel cap securely. Should fuel cap be lost,
replace it with an original manufacturer’s approved
cap. Pressurization of the tank may result from use of
non-approved cap.
•
Prevent fires by keeping the machine clean of
accumulated debris, grease, and spilled fuel.
•
Use ultra-low sulfur diesel fuel (ULSD) only.
Battery Precautions
•
Keep all sparks and flames away from batteries, as
gas given off by electrolytes is explosive.
•
Acid propelled by an explosion can cause blindness
if it comes in contact with eyes. Always wear safety
glasses when working near batteries.
•
If you come in contact with battery electrolyte solution,
wash off immediately. Chemicals can cause burns.
•
Always disconnect the battery ground cable before
working on the electrical system to avoid injury from
spark or short circuit. Electrical shock and burns can
occur.
•
To avoid electrolyte loss, DO NOT tip batteries more
than 45 degrees.
Starting and Stopping
Precautions
•
Check all around the paver to make sure there are no
people working on the machine or in the path of the
machine before starting. DO NOT start until area is
clear. Death or serious injury can occur to bystanders
from being crushed under a moving machine.
•
Check brakes, steering and other control devices in
accordance with instructions before starting. Be sure
both steering levers (joysticks) are in neutral.
•
DO NOT bypass the paver neutral-start system.
DO NOT operate the engine in an
enclosed area without proper ventilation. Exhaust
gasses are odorless and deadly.
Parking Precautions
•
Park paver on level ground whenever possible, set
steering levers in neutral and lock. Apply the parking
brake. Park the paver securely blocked on grades.
•
Before leaving operator’s station:
1. Place joysticks in neutral and lock in place.
2. Turn off all accessories.
3. Throttle back to idle.
4. Lower screed to ground.
5. Shut off engine.
•
Remove ignition key when leaving paver parked or
unattended.
Operating Precautions
•
Always comply with local regulations regarding
moving equipment on public roads and highways.
•
Know and use the hand signals required for a
particular job. Know who has the responsibility for
signaling.
•
Make sure that all lights and reflectors comply with
state and local regulations. Make sure that they are
clean, in good working order, and can be seen clearly
by all traffic.
•
DO NOT stand between the equipment and the truck
while the truck is being backed to the paver. Death or
serious injury can result from being crushed between
the two machines.
•
DO NOT ride on attachments.
•
Check all gauges and warning instruments for proper
operation. If malfunctions are found, shut down the
machine and report the problem for resolution. If the
failure causes loss of steering control, loss of brake
control, or loss of engine power, stop paver motion as
quickly as possible. Apply parking brake. Keep the
machine securely parked until the failure is corrected
or the machine can be safely towed.
Safety
LeeBoy 8510E Conveyor Paver
1-8
Summary of Contents for 8510E
