LISTED
use only with
Class 2 Type
power units
12V
DC Power
3.2
WATTS
BAR
IMPORTANT INSTRUCTIONS
1/4
KG
Never Nail or use Staples
Only power with 12VDC
Class 2 Power Source
Never apply weights or walk on strips
Apply to surface at room temperature. Keep
away from ammable materials. Surface
temperature MAX 40
°
C (104
°
F)
RGB LED LIGHT BAR Kit
Model: KIT-RGB-12T2
1-800-387-4081
Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 - 10/23/2014
Safety & Warnings
Before you begin, read all warnings and installation instructions (as they may have been updated from previous versions). Improper installation(s)
present hazards, which can result in personal injury or property damage.
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
Use only with Class 2 Type power supply.
Disconnect power before installing or servicing (at breaker point).
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local
regulations. Only power with a (listed) constant voltage Class 2 power supply (12V DC).
ONE YEAR LIMITED LIGHTING WARRANTEE
LED WORLD INC. warranties this product for one year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other
warranties expressed or implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This
Limited Warranty does not apply to damage caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims
must be submitted to them.
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected
with, the purchase of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or
otherwise, or economic loss, under any theory of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing
(including without limitation gross negligence and fundamental breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of
the possibility of such loss or damage being incurred.
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return
authorization number.
All hard-wire installation and hook-up should be done in accordance with all national and local code. Electrical hard-wire connections must be made by
qualied and licensed personnel. Instructions may change and be updated. Improper installation(s) present hazards, which can result in personal injury or
property damage.
Ÿ
Do not exceed the total length of RGB LED Bars with included items in Kit.
Ÿ
Before connecting or installing, make sure power is turned off and reduce the risk of fire and overheating, make sure all connections are tight.
Ÿ
Only install on smooth flat surface. Product must be rigidly mounted with provided clips to surface. A minimum 2 clips per bar.
Ÿ
Correct polarity is imperative: +/- is marked on the hard-wire and DC barrel connector, center is positive (+)
Ÿ
DO NOT install on flammable material or possibility of in the future. Do not install any luminaries closer than 6 inches (15.25 cm) from any curtain, or similar
combustible materials. Never apply to surface above 40
°
C (104
°
F).
Ÿ
The light and all its components cannot be mechanically pressed. Do not bend or apply pressure.
Ÿ
Voltage must not exceed 12VDC. Check that it is the correct voltage before applying powering. The voltage must be printed on the LED power supply
(driver). If it is not, do not use.
Ÿ
This is not a toy. Keep out of children's reach.
Ÿ
Keep LED Bars spaced 1” (28mm) apart if placing next to each other.
Ÿ
Not for use in mission critical, aircraft, emergency signs or lifesaving equipment.
Ÿ
Inspect installation after one hour and thereafter regularly.
Ÿ
For stationary use only. Do not subject to possible movement or pressure (or in the future). Not for in-wall use.
Ÿ
Conductors of extra-low-voltage circuits must be rigidly supported.
Ÿ
Connection to power source use Wago™ 222-413 in hardwire applications.
Ÿ
Connect only 12VDC LED bars to other 12VDC LED bar(s) (identical voltage/model).
Ensure applicable wire is installed between driver, xture and any controls in between. When choosing wire, factor in voltage drop, amperage rating and
type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in the future).
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualied electrician familiar
with low voltage wiring techniques.
