manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 78

Chapter 3: Installation

USB Protocol Suite User Manual

64

LeCroy Corporation

Input Equalization

Depending on the hardware version of your system, there are two ways to control input 
equalization. One method requires you to set three time constants, or use the defaults. 
The other method allows you to select either 

Hi

 or 

Low

, or use the default. The method 

appropriate for your connected hardware is enabled. 

For advanced users only

: You can change the values for the “other hardware” by 

checking 

Enable Both Eq modifications

. For example, you might want to do this if you 

use the same file for both Advisor T3 and Voyager M3i.

3.5.6 USB 3.0 Cabling and Signal Integrity

The Analyzer requires two connector discontinuities. In addition, bus-powered devices 
are susceptible to voltage drops on VBus.

To maintain the best possible signal integrity for all devices under test, use high-quality 
cabling and use the shortest possible cable lengths. Do not "stress" the system by using 
long or low-quality cabling that might result in signal degradation.

If you suspect signal integrity problems in capture situations, you should first try using 
shorter and higher-quality cables to see if this rectifies the problem.

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands