manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 186

Chapter 8: Decode Requests

USB Protocol Suite User Manual

172

LeCroy Corporation

For field definitions, please refer to the 

Universal Serial Bus Specification, version 2.0.

 

The USB specification is available from the USB Implementers Forum (USB-IF) at: 

8.3.3 Decoding Class Requests

Examples of a class request are Mass-Strg Class UFI CBI Requests, 
PTP Still Image Class Requests, Video Class Requests, and Wire Adapter Class 
Requests. 

To decode a class request: 

Step 1

From the USB Device Request menu, select

 Decode ... Request

 to display the 

View Fields for ... Class Requests text box.

The following figure shows a Wire Adapter Class Requests decoding:

8.3.4 Decoding Vendor Requests

To decode a vendor request: 

•

From the USB Device Request menu, select 

Decode ... Request

 to display 

the

 

View Fields for ... Vendor Requests text box.

An example of a vendor request is Command Set. 

8.3.5 Decoding Undefined USB/WUSB Device Requests

A Decoding Request may not belong to any of the defined decoding groups (Standard, 
Class, or Vendor).

USB Implementers Forum
1730 SW Skyline Blvd. 
Suite 203
Portland, OR 97221

Tel: +1/503.296.9892
Fax: +1/503.297.1090
Web: http://www.usb.org/

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands