manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 169

USB Protocol Suite

 

User Manual

Chapter 8: Decode Requests

LeCroy Corporation

 155

Chapter 8:  Decode Requests

8.1 Class and Vendor Definition Files

LeCroy Analyzers use script files to decode class and vendor requests. The script files 
are read when the application is initialized. After reading, the Analyzer decodes class and 
vendor requests as instructed by the files.

.DEC files

 represent the new method of decoding. DEC stands for “decoder” and 

describes both Class and Vendor requests in a C-like language. Each 

.dec

 file stores an 

endpoint or request decode. When the application starts, these files are loaded 
dynamically. Subdirectories are supported. 

Note: 

The 

.dec

 files listed in the following table are in the 

Scripts

 directory under the 

installation directory: 

USB Decode

USB
Decoder
Name

USB-IF

Base
Class

Codes

Sub
Class

Proto-
col
ID

Audio Class decoding 2.0

AudioClass\Audio1.0Requests.dec
AudioClass\Audio2.0Requests.dec

Audio

01h

Communications and CDC Control

Direct Line Control Model
Abstract Control Model
Telephone Control Model
Multi-Channel Control Model
CAPI Control Model
Ethernet Networking Control Model
ATM Networking Control Model
Wireless Handset Control Model
Device Management Model
Mobile Direct Line Model
OBEX Model
Communication Device Subclass/EEM

Communications\CommRequests.dec
Communications\CommInterrupt.dec
Communications\CommCDCEEM.dec

Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication
Communication

02h
02h
02h
02h
02h
02h
02h
02h
02h
02h
02h
02h
02h

01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands