manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 132

Chapter 5: Reading a Trace

USB Protocol Suite User Manual

118

LeCroy Corporation

5.41 Switch to PTP Sessions

A 

session

 is a state of persisting communication between a device and a host during 

which the connection is continuous and the login and other communication parameters 
do not change. A session begins with an 

OpenSession

 operation, which establishes the 

communications connection and parameters, and ends with a 

CloseSession

 operation. 

A session contains all object transfers (and their transactions), plus all transactions that 
do not belong to object transfers, between an OpenSession operation and a 
CloseSession operation. For PTP, all PTP Object Transfers and all PTP Transactions 
that occur from the OpenSession operation to the CloseSession operation is a single 

PTP Session

. 

The PTP Session trace viewing level is the highest PTP level.
To view PTP sessions, switch to the PTP Session trace viewing level:

•

Click

on the toolbar.

OR

•

Select 

View > PTP Session Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

PTP 

Session

, and then click 

OK.

5.42 Switch to SCSI Operations

To view SCSI operations, switch to SCSI Operations viewing level:

•

Click

on the toolbar.

OR

•

Select 

View > SCSI Operation Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

SCSI Operation

, and then click 

OK.

5.42.1 SCSI Metrics

The SCSI Metrics are:
•

Address 

•

Number Of Transfers

: Total number of transfers that compose the SCSI operation

•

Response Time

: Time to transmit on the USB link, from the beginning of the first 

transfer in the SCSI operation to the end of the last transfer in the SCSI operation

•

Latency

: Time from the transmission of the SCSI command to the first data trans-

mitted for the SCSI IO operation

•

Data To Status Time

: Time between the end of data transmission for the SCSI 

operation and the status transfer

•

Payload

: Number of payload bytes transferred by the SCSI operation

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands