manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 130

Chapter 5: Reading a Trace

USB Protocol Suite User Manual

116

LeCroy Corporation

5.36 Switch to Host Wire Adapter Transfer View

A 

Host Wire Adapter Transfer

 is one or more wire adapter segments or one or more 

transfers between a PC and a host wire adapter. To view host wire adapter transfers, 
switch to the Host Wire Adapter Transfer trace viewing level.

To select the Host Wire Adapter Transfer trace viewing level: 

•

Click

on the toolbar.

OR

•

Select 

View > HWA Transfer Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

HWA Transfer

, and then click 

OK.

5.37 Switch to Device Wire Adapter Segment View

A 

Device Wire Adapter Segment

 is one or more transfers between a PC and a device 

wire adapter. To view device wire adapter segments, switch to the Device Wire Adapter 
Segment trace viewing level.

To select the Device Wire Adapter Segment trace viewing level: 

•

Click

on the toolbar.

OR

•

Select 

View > DWA Segment Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

DWA Segment

, and then click 

OK.

5.38 Switch to Device Wire Adapter Transfer View

A 

Device Wire Adapter Transfer

 is one or more wire adapter segments or one or more 

transfers between a PC and a device wire adapter. To view device wire adapter transfers, 
switch to the Device Wire Adapter Transfer trace viewing level.

To select the Device Wire Adapter Transfer trace viewing level: 

•

Click

on the toolbar.

OR

•

Select 

View > DWA Transfer Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

DWA Transfer

, and then click 

OK.

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands