Leadshine ELP Series User Manual Download Page 148

Page: 148 / 165

User Manual for ELP Servo

www.leadshine.com

148

2 velocity mode

3 homing

4 stop

Bit4:

INS,

0 do not interrupt

1 interrupt

（

All interrupt now

）

Bit5:

OVLP

，

0 do not overlap

1 overlap

Bit6-7:

0 absolute position

1 relative to command

2 relative to motor

Bit8-13

：

0-15 Jump to the corresponding path

Bit14

：

JUMP:

0 do not jump

1 jump

Pr9.01

Path0 position H

0X6201

Pr9.02

Path0 position L

0X6202

Pr9.03

Path0 speed

rpm

0X6203

Pr9.04

Path0 acceleration

ms/1000rpm

0X6204

Pr9.05

Path0 deceleration

ms/1000rpm

0X6205

Pr9.06

Path0 Pause time

The pause of path, delay time parameter etc, refer to PR

motion type for specific meaning.

0X6206

Pr9.07

Special Parameters

Path 0 is mapped to Pr8.02 parameters

0X6207

And so on

Each path occupy eight parameters

Set path 1~ path15 as same as path 0 .

Implement choice and start of actions by write corresponding instructions into 0x6002 (Pr8.02), to select which path

to run.

9.4.5 Immediately trigger method

Fixed trigger is limited by 16 path, but immediately trigger method is flexible. It is written to the current

path at each time, at the same time trigger the operation of this path. Trigger position, speed , homing by a

data frame.

This method adopt path0 to implement, path0 has 8 data in total, the last data Pr9.07 of it will mapped to

Pr8.02, write in 0x10 can trigger path0 motion immediately.

As below procedure

：

1. Firstly, configure homing and path which need to run, set these parameters by communication or set these

parameters and save with upper computer. (homing must be configured)

2. Enable drive.

Summary of Contents for ELP Series






































































































































































Search results

Summary of Contents for ELP Series

Reviews:

Leadshine ELP Series, User Manual, Page: 148 / 165

Search results

Summary of Contents for ELP Series

Reviews: