Leadshine CS-D808 User Manual Download Page 14

                                                                                  CS-D808 Closed Loop Stepper Drive User Manual                                                             

 

 

Page | 11   

 

13. Warranty

 

Twelve Month Warranty   

Leadshine Technology Co., Ltd. warrants its products against defects in materials and workmanship for a period of 12 

months from shipment

 

out of factory. During the warranty period, Leadshine will either, at its option, repair or replace 

products which proved to be defective. 

Exclusions                                                                                                                           

The  above  warranty  does  not  extend  to  any  product  damaged  by  reasons  of  improper  or  inadequate  handlings  by 

customer,  improper  or  inadequate  customer  wirings,  unauthorized  modification  or  misuse,  or  operation  beyond  the 

electrical specifications of the product and/or operation beyond environmental specifications for the product. 

Obtaining Warranty Service                                                                                     

To obtain warranty service, please contact your seller to obtain a returned material authorization number (RMA) before 

returning product for service. 

Shipping Failed Products         

                                                                                           

If your product fail during the warranty period, please contact your seller for how and where to ship the failed product 

for warranty or repair services first, you can also e-mail customer service at 

[email protected]

 to obtain a returned 

material authorization number (RMA) before returning product for service. Please include a written description of the 

problem along with contact name and address. 

 

Summary of Contents for CS-D808

















Reviews: