background image

 

User

s Manual   

For

 

 

DM432 

Fully Digital Stepping Driver

 

Version 1.0 

©

2008 All Rights Reserved

 

Attention: Please read this manual carefully before using the driver! 

 

 

3/F, Block 2, Nanyou Tianan Industrial Park, Nanshan Dist, Shenzhen, China 

T: (86)755-26434369            F: (86)755-26402718 

Web site: 

www.leadshine.com

      E-Mail: 

[email protected]

 

 

 

The

 

content  in  this  manual  has  been  carefully  prepared  and  is  believed  to  be  accurate,  but  no 

responsibility is assumed for inaccuracies. 

Leadshine  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein  to 

improve reliability, function or design. Leadshine does not assume any liability arising out of the 

application or  use of  any  product  or  circuit described herein;  neither  does  it  convey  any  license 

under its patent rights of others.   

Leadshine

s general policy does not recommend the use of its products in life support or aircraft 

applications wherein a  failure or malfunction of the product may directly threaten life or injury. 

According to Leadshine

s terms  and conditions of sales, the user of Leadshine

s products in life 

support or aircraft applications assumes all risks of such use and indemnifies Leadshine against all 

damages. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

©

2008 by Leadshine Technology Company Limited. 

All Rights Reserved

 

Summary of Contents for DM432


















Reviews: