background image

User’s Manual  

For

 

 

DM422C 

Fully Digital Stepping Drive 

Version 1.0 

©2009 All Rights Reserved

Attention: Please read this manual carefully before using the Drive! 

 

The content in this manual has been carefully prepared and is believed to be accurate, but no
responsibility is assumed for inaccuracies.

Leadshine reserves the right to make changes without further notice to any products herein to
improve reliability, function or design. Leadshine does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license
under its patent rights of others.

Leadshine

s general policy does not recommend the use of its products in life support or aircraft

applications wherein a failure or malfunction of the product may directly threaten life or injury.
According to Leadshine

s terms and conditions of sales, the user of Leadshine

s products in life

support or aircraft applications assumes all risks of such use and indemnifies Leadshine against all
damages.

©

2009 by Leadshine Technology Company Limited. 

All Rights Reserved

[email protected] 

www.dold-mechatronik.de

DOLD Mechatronik

Sarach 10 – D-77790 Steinach

Telefon: +49 7832 / 9744670

Summary of Contents for DM422C

















Reviews: