Le Maitre Salamander Quad Pro User Manual Download Page 17 | Manualshive

Page: 17 / 23

background image

Le Maitre Ltd.

Salamander Quad Pro User Manual

16

8.

Maintenance

Please note:

While the Salamander Quad Pro contains several components that have been

designed to be user-serviceable, the maintenance procedures described in this section
should only be performed by qualified personnel. The manufacturer cannot be held
responsible for events occurring due to incorrect maintenance of this machine.

Please note:

All the procedures described in this section should be performed with the

Salamander Quad Pro isolated from any power supply, after the unit has been allowed to
cool for at least 10 minutes.

The Salamander Quad Pro features two service panels secured by 4xM4 bolts. Removal of these
service panels allows access to the majority of user-serviceable components within the Salamander
Quad Pro:

Figure 4: Salamander Quad Pro Firing Mechanism

«
...
15
16
17
18
19
...
»

Summary of Contents for Salamander Quad Pro
























Reviews:

No comments

Related manuals for Salamander Quad Pro

Brand: Attwood Pages: 2

Robus RVB007RGB10I65

Brand: LED Group Pages: 2

Brand: SHOWTEC Pages: 12

Brand: HAMPTON BAY Pages: 12

Brand: Dale Tiffany Pages: 2

Brand: Whelen Engineering Company Pages: 3

VarioContour 0024

Brand: LED Linear Pages: 4

FOS 100 FULL RGBW

Brand: DTS Pages: 32

Brand: Somogyi Elektronic Pages: 2

Brand: Avlite Pages: 20

Lighting Systems EG2-6

Brand: Lightolier Pages: 5

UNISIZEplus 4446-0FW120

Brand: DOTLUX Pages: 2

MaMo Nouchies Kokoro LED

Brand: Ingo Maurer Pages: 10

Brand: X4-Life Pages: 13

NIMBUS Connect TT

Brand: Häfele Pages: 2

HALPRM-PS-1000WMH

Brand: Larson Electronics Pages: 2

EPLFL-26W-P-LED-25

Brand: Larson Electronics Pages: 3

Brand: Larson Electronics Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands