--
To reduce the risk of injur y:
•
Do not operate the unit until the back is installed and locked.
NOTICE:
Do not plug the transformer in until instructed.
1. The power transfor mer is secured to the seat swing. Carefully cut the ca ble tie
and set the power transfor mer aside.
2. Install the back.
•
Lay the back across the ar ms of the body (F
I G U R E
1).
•
Lift the back at a slight angle and align the brackets on the back with
•
the brackets on the body (F
I G U R E
2).
•
Lower the back onto the body, making sure the back and body brackets
are completely engaged.
•
Lock the brackets by using a screwdriver to push down the locking levers (F
IGURE
3).
3. Locate the massage connector s .
•
Stand at the side of the chair and push the back rearward to recline the seat and back.
•
Gently tip the chair forward to rest on its ar ms and the top of the back,
revealing the under side of the chair and the connector s .
4. Identify the three connections you will make.
•
Locate the five wires with connectors. Four wires are located next to the rear body rail.
One wire is located next to the body side panel; if the chair has an arm storage pocket
it is located on the left side and if the chair has an arm storage compartment it is
located on the right side.
•
The two square-shaped connectors are for the Vibrating Motor connection (F
IGURE
1 & 4).
•
The one smaller, round-shaped connector is for the Power Transformer
connection (F
IGURE
1 & 4).
•
The two larger, round-shaped connectors with white dots are for the Hand Wand
connection (F
IGURE
1 & 4).
5. Connect the Vibrating Motor s .
•
Align the two square-shaped Vibrating Motor connectors (some of the connector pins
are square, others are round).
•
Push the connector s together until they lock (F
IGURE
5).
6. Connect the Hand Wand.
•
Align the w hite dots on the Hand Wand connector s .
•
Push the connectors together until they are secured with no gaps between them (F
IGURE
5).
7. Connect the Power Transfor mer.
•
Plug the Power Transformer connector into the connector located next to the rear body rail
so the cord is to the back of the chair, away from the bottom of the base and, mechanism.
Make sure the connectors are secured with no gaps between them (F
IGURE
5).
8. Retur n the chair to its upr ight position.
•
Hold the Power Transformer cord
away from the base
and gently tip the chair back,
until it is completely upright and setting on its base.
Make sure the Power Transformer
cord is not pinched
between the base and the floor. Return the seat and back to the
upright position.
9. Choose a location for the chair that is close to an electr ical outlet and
proceed to the Operating Instr uctions .
NOTICE:
To prevent damage to the connectors and cords, it is important to
unfasten all connections prior to removing the back. Reverse the Assembly
Instruction steps when removing the back.
La-Z-Touch
®
10-Motor Massage & Heat Recliner
Assembly Details:
F
I G U R E
1
Power Transfor mer Connector
Hand Wand Connector
Vibrating Motor Connector
Hand Wand Connector
Vibrating Motor Connector
Power Transfor mer
F
I G U R E
2
Body
Bracket
Back
Bracket
Back Bracket
Locking
Lever
Locked
Position
(Figure shown without electrical connections)
F
I G U R E
3
Power
Transfor mer
Connection
Power
Transfor mer
Connector
Hand
Wand
Connector s
Hand
Wand
Connection
Vibrating Motor
Connector s
Vibrating Motor
Connection
F
I G U R E
4
F
I G U R E
5
15
14
La-Z-Touch
®
10-Motor Massage & Heat Recliner
Assembly Instr uctions:
WARNING
