Not to Scale
The use of non-clutching impact drivers to install this hardware will automatically void the warranty.
All product specifications are subject to change.
Phone: 1-800-267-1236
www.lawrencehardware.com
Fax: 1-800-892-7026
676 Petrolia Road
Toronto, Ontario M3J 2V2
LH3000
Instructions
and Template
Template
Ø55
60/70
58
26
41.6
3.7
Ø3
Template
3⁄8 1⁄8 3⁄8 5⁄32 3⁄4
1⁄8”
2 1⁄8”
1 5⁄8”
5⁄32”
1”
2 3⁄8 or 23⁄4
Phone 1-800-435-9568
www.lawrencehardware.com
Fax 1-800-892-7026
TQ2
TQ2
4. Reversible Levers
5. Install Outside Lever
Insert spindle through latch.
Press flush against door.
6. Install Inside Lever
Install inside lever and
tighten screws until lock is firm.
7. Install Strike
a. Close door to make horizontal
centre line of strike.
A.
B.
C.
c. Install strike and tighten screws.
b. Measure one half of door thickness
from door stop and mark vertical
centre line of strike.
Drill 1"
(
25.4mm
)
hole 1/2"
(
13mm
)
deep at intersection of horizontal
and vertical line of strike.
Match screw holes on strike with
centre lines on jamb.
Mark outline and chisel 1/16"
(
1.6mm
)
deep for strike.
Handle can be only
installed when the timing
of "emergency release"
is set in the position
shown below.
RIGHT
HAND DOOR
LEFT
HAND DOOR
54mm (2-1/8")
FOR BACKSET
(
)
70mm 2-3/4"
FOR BACKSET
(
)
60mm 2-3/8"
Rev. 13/10/2011
45 40 35
1-3/4"
1-3/8"
1-9/16"
2-1/4" (57mm)
5.5mm 7/32"
hole for metal
door only
(
) x 2
Make 1"
(
25.4mm
)
hole at center of door edge.
Fold on dotted line and fit on door edge
TEMPLATE
Fold on dotted line and fit on door edge
a. Please check the levers are unlocked
(
Entrance sets only
)
.
Depressing lever catch with hand tool to release outside lever and pulling lever off.
Taking apart off the and cylinder from outside lever.
b. Reversing the levers from outside to inside
/
inside to out side, putting the cylinder
on the outside lever
(
Entrance sets only
)
.
Please do the same procedures for inside lever.
c. Pushing handles in until catch clicks. Make sure levers are retained by lever.
Backset is a distance from the door edge to the centr of the hole on door face.
Some locks are supplied with adjustable latch which can fit 2-3/8"
(
60mm
)
or 2-3/4"
(
70mm
)
backset.
Just follow the steps shown below to change backset.
e
a. This latch is set for
2-3/8"
(
60mm
)
backset.
b. Keep spindle cam in correct
position as illustrated.
Pull spindle cam all the way
to right.
c. Your latch is now set for 2-3/4"(70mm) backset.
To reset 2-3/8"(60mm) backset, just push spindle
cam back to left side.
Please make sure that the cams are staying with
square shape.
Some locks are supplied with 4-way latch which can fit mortise in or drive in.
a. This latch is for mortise in.
b. Rotate latch face clockwise 20
°
and pull out latch face.
c. This latch is for drive in.
A.
B.
C.
2
2
3
3
8
8
/
/
/
/
4
4
3
3
2
2
""
"
"
"
"
"
"
2
2
3
3
4
4
/
/
/
/
8
8
3
3
2
2
A.
B.
C.
INSTRUCTIONS FOR INSTALLATION OF TUBULAR LEVERSETS
Latch Backset Adjustment
Latch Face Plate
1. Mark Door with Template
a. Start 36"
(
914mm
)
from floor, fold and apply template
from floor, mark centre of door edge.
b. Select 2-3/8"
(
60mm
)
or 2-3/4"
(
70mm
)
backset as
desired and mark centre of hole on door face.
2. Drill Holes
a. Drill 2-1/8"
(
54mm
)
hole on door face, from both sides to
avoid wood splitting.
b. Drill 1"
(
25.4mm
)
hole for latch.
(
refer step 3c for drive-in latch
)
3. Install Latch
a. Insert latch in hole, mark outline of faceplate and chisel 5/32"
(
4mm
)
deep.
b. Insert latch and tighten screws.
c. For drive in latch, drill 31/32"
(
24.6mm
)
hole and press latch until it is
flush with door edge.
A.
B.
C.
TQ2
TQ2
TQ2
TQ2
Installation sheet for Tubular latchbolt (3000 series, October 2014)
1. Door face prep for either 2 3/8 or 2 ¾” backset
2. Door edge prep 1” x 2 ¼” 5/32” (4MM) 1” cross bore.
Phone 1-800-435-9568
www.lawrencehardware.com
Fax 1-800-892-7026
Backset is a distance from the door edge to the centr of the hole on door face.
Some locks are supplied with adjustable latch which can fit 2-3/8"
(
60mm
)
or 2-3/4"
(
70mm
)
backset.
Just follow the steps shown below to change backset.
e
a. This latch is set for
2-3/8"
(
60mm
)
backset.
b. Keep spindle cam in correct
position as illustrated.
Pull spindle cam all the way
to right.
c. Your latch is now set for 2-3/4"(70mm) backset.
To reset 2-3/8"(60mm) backset, just push spindle
cam back to left side.
Please make sure that the cams are staying with
square shape.
Some locks are supplied with 4-way latch which can fit mortise in or drive in.
a. This latch is for mortise in.
b. Rotate latch face clockwise 20
°
and pull out latch face.
c. This latch is for drive in.
A.
B.
C.
22
33
88
//
//
44
33
22
""
""
""
""
22
33
44
//
//
88
33
22
A.
B.
C.
INSTRUCTIONS FOR INSTALLATION OF TUBULAR LEVERSETS
Latch Backset Adjustment
Latch Face Plate
1. Mark Door with Template
a. Start 36"
(
914mm
)
from floor, fold and apply template
from floor, mark centre of door edge.
b. Select 2-3/8"
(
60mm
)
or 2-3/4"
(
70mm
)
backset as
desired and mark centre of hole on door face.
2. Drill Holes
a. Drill 2-1/8"
(
54mm
)
hole on door face, from both sides to
avoid wood splitting.
b. Drill 1"
(
25.4mm
)
hole for latch.
(
refer step 3c for drive-in latch
)
3. Install Latch
a. Insert latch in hole, mark outline of faceplate and chisel 5/32"
(
4mm
)
deep.
b. Insert latch and tighten screws.
c. For drive in latch, drill 31/32"
(
24.6mm
)
hole and press latch until it is
flush with door edge.
A.
B.
C.
TQ2
TQ2
TQ2
TQ2
3. Handing of latch-bolt, turn faceplate approximately 20 degree and remove, turn latch-bolt
over and reinstall faceplate. Note this change may not be required.
4. handing privacy button if required. Move screw in privacy button from the inside of the door to
the outside of the door if needed. Note; this change may not be needed.
3. To change hand if required, hold latch tube with one hand and rotate faceplate 180
degrees, take care to ensure both tabs stay engaged between the latchtube and faceplate
tabs holding the faceplate to the latchtube stay engaged.
1. Door face prep for either
2 3/8” or 2 ¾” backset
2. Dooredge prep
1” X 2 1/4” X 5/32”
3. To change hand if required,
simply hold latch tube with one
hand and rotate latch bolt with
other hand .
4. Threaded portion of latch bolt
must be on the inside of the door
5. Emergency release hole on
outside rose
6. In emergency push small object
into outside hole to release privacy
function and gain entry
