LAWO V_pro8 Installation & Operation Manual Download Page 23

Page: 23 / 109

V_pro8 Manual

V1.0/2

Installation & Configuration
Powering On

Powering On

The

pro8

has no on/off switch but starts automatically when either power supply is connected to the

mains. Please install a master system power switch where applicable.

You will hear the fans begin to operate, and the LEDs on the front of the unit illuminate as follows:

STATUS LED

Blue

= unit is booting.

Green

= ready for operation.

Flashing Yellow

= network activity.

Red

= system error. If the

STATUS

LED is red, then try powering the unit off and on. For

further assistance, please contact your local Lawo representative or email

[email protected]

PSU 1 and PSU 2 LEDs

Green

= power supply is active.

Off

= power supply is inactive (no mains input or internal PSU is faulty).

The system takes approximately 7 seconds to boot from power on, and loads the latest settings.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands