LAUREL LAUREATE 2 Series Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 64

background image

- 49 -

20. INSTRUMENT SETUP VIA PC

Instrument Setup (IS) Software is a PC program which is at no charge and is easier to learn
than front panel programming. With the meter connected to the PC, it allows uploading, editing
and downloading of setup data, execution of commands under computer control, listing,
plotting and graphing of data, and computer prompted scaling. With the meter unconnected
to a PC, it provides quick selection of jumper locations and a printable display of menu
selections for front panel setup.

SOFTWARE INSTALLATION

Under Windows 7 or 10,

set User Account Control (UAC) to “Never Notify” so that IS software

can write files. Turn off an restart your computer. Download

IS2*.exe

onto your PC from our

website. Double-click on the downloaded file to unzip it into a directory, such as

c:\temp

.

Within that directory, double-click on

setup.exe

to install the software on your PC.

PREREQUISITES FOR CONNECTED USE

1)

PC with an available communication port.

2)

Meter to be set up.

3)

Communication board in meter. This board
can be removed following meter setup.

4)

Communication cable from meter to PC.

5) Instrument Setup

software.

ESTABLISHING COMMUNICATIONS

Connect the meter and PC. Apply power to the meter. Be sure that the meter is in Run Mode,
not Setup Mode. To start the software from Windows, click on

Start

=>

Programs

=>

IS2

=>

IS2

. Click on

RS232

=>

Establish

. The program will temporarily set the selected Com port to

the required baud rate, parity, data bits and stop bit. Once communications have been
established, click on

Main Menu

. The software will sense the type of meter and installed

boards, but it cannot sense jumpers positions nor set jumpers for you. If the computer is not
connected to a meter, select

DPM

and

Series 2

.

«
...
47
48
49
50
51
...
»

Summary of Contents for LAUREATE 2 Series

































































Reviews:

No comments

Related manuals for LAUREATE 2 Series

Brand: Aaronia Pages: 47

Brand: Xylem Pages: 24

Power Xpert PXM 4000

Brand: Eaton Pages: 28

Brand: janitza Pages: 6

Brand: janitza Pages: 36

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Nellcor Pages: 104

Brand: Olympus Pages: 12

Brand: Sensia Pages: 16

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brand: horiba Pages: 175

Brand: Raytech Pages: 7

Brand: OmegaWatt Pages: 9

Engine Analyzer Series

Brand: ACCEL DFI Pages: 39

Brand: SBS Pages: 17

Brand: QuantAsylum Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands