background image

6

Laundrylux

112999-1

Program Selection ____________________

NOTE: Programs are stored in the Phase 5 coin
microprocessor controller (computer) memory and are
cataloged as PL.

Temperature Display Mode

By closing the PS located on the back side of the Phase 5

coin microprocessor controller (computer), the L.E.D. display

will read the temperature in the dryer in either Fahrenheit (°F)

or Celsius (°C), depending on how the temperature conversion

status is in PL01.   The temperature display mode can be

activated while the dryer is in the operating cycle, or of

f.  While

in the operating cycle, the circuit indicators are visible for

troubleshooting purposes.

NOTE: The dryer cannot be started while the Phase 5 coin
microprocessor controller (computer) PS is closed, unless
the cycle was already in progress.

Right Coin Count (rCC)/Left Coin Count (LCC)

The “HI TEMP” key lets the operator review the coin counters.

If the operator presses the “HI  TEMP” key, the computer

displays “_LCC.”   The operator could then press either the

“PERM PRESS” key to view the “Lef t Coin Count” or the “HI

TEMP” key and the computer would display “_rCC.”   Again,

the operator could press the “PERM PRESS” key to view the

“right coin count.”  While displaying the coin count, if the

operator presses the “HI  TEMP” key the computer then

displays “CxCC” (x = “r” or “L”) to indicate “clearing” the coin

count.  The operator then presses the “PERM PRESS” key to

clear the coin count or the “HI  TEMP” or “LO  TEMP” key to

exit without clearing the coin count.

Automatic Review of Program Location

This selection allows for the  AUTOMATIC REVIEW of what

the program locations are set (programmed) for , thereby

eliminating the need to go into each and every PL manually

for verification.  By closing the PS with no cycle in progress,

the L.E.D. display will read the temperature in the dryer

.  Then,

by pressing the “LO  TEMP” key, the L.E.D. display will read

“PLOC” for 1-second.  Then, the Phase 5 coin microprocessor

controller (computer) will go into the Automatic Review Mode,

the Program Location numbers (i.e., PL01, PL02, etc.) will not

be shown and each parameter (i.e., “°FAr,” “tInE,” “Grd,” etc.)

will be displayed for approximately 1-second each.   The

Automatic Review can be stopped/exited at any time by simply

pressing the “PERM PRESS” key , at which time the L.E.D.

display will read “0000” for 1-second and then return to the

Temperature display mode.

PL01 – Temperature Conversion Status

This program controls whether the temperature related

programs will be operated in Fahrenheit (°F) or Celsius (°C).

The programs affected are:
1. Temperature Display Mode
2. Selection Cycling Temperatures
3. Cool Down Temperatures

Automatic Mode (AUtO) Patent No. 4,827,627

When this parameter (“AUtO”) is selected, the dryer will run

for a preset level of dryness (PL02) or until the programmed

automatic maximum time (PL14) has expired.
At the end of the drying cycle, the dryer will go into the cool

down cycle for the time period programmed (PL04, PL06, or

PL08) or until the temperature has dropped to the programmed

cool down temperature (PL04, PL06, or PL08).

NOTE: Due to humidity, atmospheric pressure, percentage
of extraction, etc., the desired dryness level may vary.  It is
suggested that the owner determine which level of dryness
(90% to 100%) is best suited for his/her application by
experimenting with a few test loads.

When programming, to use the Automatic Mode (“AUtO”)
(Patent No. 4,827,627), the following parameter/programs
need to be checked and/or changed accordingly:

PL01 .......... “AUtO”

“FrEE” or “Coin” (coins required to start)

PL02 .......... “PdrY” (percent dry from 90% to 100%)

PL14 .......... “Adrt” (maximum auto dry time)

PL17 .......... “A” and “b” Factors

Summary of Contents for DAWS0 SERIES







































Reviews: