Lauda PTT Operating Instructions Manual Download Page 21

Page: 21 / 23

PTT

YAME0020 / 30.06.11

Index

6.6

Accessories, replacement parts

Description

Application / function

LAUDA

order no.

PTT cover (transparent plastic cover)

Reduction of temperature changes in the vicinity of the
surface and ingress of dust (tensiometry), wind protec-
tion, reduction of evaporation.

HGH 188

Temperature sensor

Sensor for determining the actual temperature.

DU 711

Sample beaker

Sample beaker D.60x32 mm, pack of 10

EG 011

Disposable syringe

Filling and topping up tempering liquid.

EGP 012

PTFE stirring rod (diameter 4.5 mm,
length 15 mm)

Mixing the sample for optimum heat transfer

EZ 265

To avoid erroneous shipments please quote the device type and number from the rating label. The
rating label is located on the back panel of the device.

Rating label with device details

(LMTZ831-nn-nnnn)

Summary of Contents for PTT
























Search results

Summary of Contents for PTT

Reviews:

Related manuals for PTT

Brands by name

Popular brands

Lauda PTT, Operating Instructions Manual

Search results

Summary of Contents for PTT

Reviews:

Related manuals for PTT

Brands by name

Popular brands