Lattice Semiconductor MachXO5-NX Development Kit User Manual Download

Page: 25 / 64

MachXO5-NX Development Board

Preliminary Evaluation Board User Guide

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-EB-02052-0.90

U4 Pin Number

Net Name

MachXO5-25 Ball Location

GND

—

GND

—

PWR_3-3V*

—

CH2_DATA1_P

U10

CH2_DATA1_N

V10

PWR_5-0V*

—

SDA1

SCL1

Notes:

Signal is optionally connected to power source through resistor DNI.

12 V power needs external supply from pin 8 of J4.

Table 8.8. FX12 U5 Header Pin Connections

U5 Pin Number

Net Name

MachXO5-25 Ball Location

CH1_DCK_P

Y11

CH1_DCK_N

W11

GND

—

CH1_DATA0_P

V11

CH1_DATA0_N

U11

GND

—

CH1_DATA2_P

V12

CH1_DATA2_N

U12

GND

—

FX_SN

FX_SCLK

PWR_12V**

—

SDA2

SCL2

GND

—

CH3_DATA0_P

T11

CH3_DATA0_N

R11

GND

—

CH3_DCK_P

Y12

CH3_DCK_N

W12

PWR_12V**

—

RESETN

PWR_5-0V*

—

CH1_DATA1_P

Y14

CH1_DATA1_N

W14

PWR_3-3V*

—

CH1_DATA3_P

Y13

CH1_DATA3_N

W13

PWR_1-8V

—

FX_MOSI

FX_MISO

PWR_1-8V*

—

GND

—

GND

—

PWR_3-3V*

—

Summary of Contents for MachXO5-NX Development Kit

































































Search results

Summary of Contents for MachXO5-NX Development Kit

Reviews:

Related manuals for MachXO5-NX Development Kit

Brands by name

Popular brands

Lattice Semiconductor MachXO5-NX Development Kit, User Manual

Search results

Summary of Contents for MachXO5-NX Development Kit

Reviews:

Related manuals for MachXO5-NX Development Kit

Brands by name

Popular brands