Lattice Semiconductor ECP5 Versa Technical Notes Download | Manualshive

Page: 8 / 78

background image

8

ECP5 and ECP5-5G Hi

g

h-Speed I/O Interface

Figure 7. GDDRX1_RX.SCLK.Aligned Interface (Dynamic Data/Clock Delay)

Interface Requirements

• The clock input must use a PCLK input so that it can be routed directly to the DLLDELD input

• The user must set the timing preferences as per section “Timing Analysis Requirement”

GDDRX2_RX.ECLK.Centered

Generic Receive DDR with the 2X gearing using Edge Clock Tree (ECLK). Input clock is centered to the input Data.
This interface must be used for speeds above 200

MHz

.

This DDR interface uses the following modules:

• IDDRX2F element for X2 mode to capture the data

• The incoming clock is routed to the Edge clock (ECLK) clock tree through the ECLKSYNCB module

• CLKDIVF module is used to divide the incoming clock by 2 to generate the SCLK

• Static data delay element DELAYG to delay the incoming data enough to remove the clock injection time

• Optionally the user can choose to use Dynamic Data delay adjustment using DELAYF element to control the

delay on the DATA dynamically. DELAYF will also allow user to override the input delay set. The type of delay
required can be selected through Clarity Designer

• DEL_MODE attribute is used with DELAYG and DELAYF element to indicate the interface type so that the cor-

rect delay value can be set in the delay element

• The ECLKBRIDGE can be optionally enabled if the data bus will be crossing over between the left and right sides

of the device. If ECLKBRIDGE is enabled then the ECLKBRIDGECS element should be used in the interface
before the ECLKSYNCB element. This element can be enabled through Clarity Designer.

• The startup synchronization soft IP (GDDRX_SYNC) is required for this interface to tolerate the skew between

the ECLKSYNCB Stop input and the Reset to the DDR and CLKDIV modules.

The following figures show the static delay and dynamic delay options for this interface.

Data_LoadN

Data_Move

Data_Direction

A

DELAYF

LOADN

MOVE

DIRECTION

CFLAG

Datain

Q[0]

Q[1]

Clkin

DLLDELD

Z

A

DDRDEL

LOADN

MOVE

DIRECTION

CFLAG

IDDRX1F

SCLK

D

Q0

Q1

RST

CLK

RST

UDDCNTLN
FREEZE

DDRDEL

LOCK

DDRDLLA

DCNTL[7:0]

Dcntl[7:0]

Clock_LoadN

Clock_Move

Clock_Direction

Clock_CFlag

Data_CFlag

7

Z

Primary

(optional)

DEL_MODE=

SCLK_ALIGNED

STOP

DLL _LOCK

FREEZE

UDDCNTLN

DLL _RESET

DDR _RESET

SYNC_CLK
RST

UPDATE

Sync_clk

sync_reset

Update

READY

(open)

RX_SYNC

(soft IP)

Sclk

«
...
6
7
8
9
10
...
»

Summary of Contents for ECP5 Versa















































































Reviews:

No comments

Related manuals for ECP5 Versa

Brand: KaVo Pages: 16

Brand: Parker Research Corp Pages: 3

Brand: S.I.T.A. Pages: 32

Brand: Parker Pages: 54

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: NARGESA Pages: 50

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: JB-Lighting Pages: 40

Brand: GARANT Pages: 239

Brand: p-light Pages: 36

Brand: iHealth Pages: 8

Brand: jablotron Pages: 2

Brand: jablotron Pages: 2

Brand: Laser Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands